Original catalog preview
Model · SPC/SSPC
SPC/SSPC Series Rigid Couplings
Overview

| Model | D [mm] | L [mm] | D1/D2 Bore Diameter Range [mm] | L1 [mm] | L2 [mm] | L3 [mm] | K [mm] | M | Tightening Torque [N.m] |
|---|---|---|---|---|---|---|---|---|---|
| SPC-16 | 16 | 16 | 4~6 | 3.75 | 7.5 | 8 | 5 | 1-M2.5 | 1 |
| SPC-20 | 20 | 20 | 5~8 | 4.75 | 9.5 | 10 | 6.5 | 1-M2.5 | 1 |
| SPC-25 | 25 | 25 | 6~12 | 6 | 12 | 12.5 | 9 | 1-M3 | 1.5 |
| SPC-32 | 32 | 32 | 8~16 | 7.75 | 15.5 | 16 | 11 | 1-M4 | 3.5 |
| SSPC-16 | 16 | 16 | 4~6 | 3.75 | 7.5 | 8 | 5 | 1-M2.5 | 1 |
| SSPC-20 | 20 | 20 | 5~8 | 4.75 | 9.5 | 10 | 6.5 | 1-M2.5 | 1 |
| SSPC-25 | 25 | 25 | 6~12 | 6 | 12 | 12.5 | 9 | 1-M3 | 1.5 |
| SSPC-32 | 32 | 32 | 8~16 | 7.75 | 15.5 | 16 | 11 | 1-M4 | 3.5 |
For set screws, M denotes the nominal screw size; the number indicates the quantity per side.



Models & specifications
| Model | Maximum Shaft Diameter [mm] | Rated Torque [N.m] | Maximum Torque [N.m] | Maximum Speed [rpm/mm] | Moment of Inertia [kg.m²] | Weight [g] |
|---|---|---|---|---|---|---|
| SPC-16 | 6 | 1 | 2 | 3900 | 3.0×10⁻⁷ | 8.3 |
| SPC-20 | 8 | 2.5 | 5 | 3100 | 8.7×10⁻⁷ | 15 |
| SPC-25 | 10 | 4.5 | 9 | 2500 | 2.7×10⁻⁶ | 29 |
| SPC-32 | 16 | 10 | 20 | 1900 | 7.0×10⁻⁶ | 48 |
| SSPC-16 | 6 | 0.3 | 0.6 | 3900 | 3.0×10⁻⁷ | 22 |
| SSPC-20 | 8 | 0.5 | 1 | 3100 | 8.7×10⁻⁷ | 41 |
| SSPC-25 | 10 | 1 | 2 | 2500 | 2.7×10⁻⁶ | 80 |
| SSPC-32 | 16 | 2 | 4 | 1900 | 2.4×10⁻⁵ | 150 |
Maximum speed does not account for dynamic balancing. Moment of inertia and weight are values at the maximum bore diameter.
| Model | Standard Bore D1-D2 [mm]: 3 | 4 | 5 | 6 | 6.35 | 8 | 9.525 | 10 | 12 | 14 | 15 | 16 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SPC-16 | ● | ● | ● | |||||||||
| SPC-20 | ● | ● | ● | ● | ||||||||
| SPC-25 | ● | ● | ● | ● | ● | |||||||
| SPC-32 | ● | ● | ● | ● | ● | |||||||
| SSPC-16 | ● | ● | ● | |||||||||
| SSPC-20 | ● | ● | ● | ● | ||||||||
| SSPC-25 | ● | ● | ● | ● | ● | |||||||
| SSPC-32 | ● | ● | ● | ● | ● |
● Standard bore sizes. This series is not stocked; please contact sales for lead times when ordering. The recommended shaft tolerance is h6 to h7 and must not exceed h8. When installing on a D-cut shaft, pay attention to the position of the D-flat; see page 4.
