Fixing Rings

DNV Clamp-Type Shaft Collar Series

DNV Clamp-Type Shaft Collar Series

DNV series clamp-type shaft collars are designed to secure shafts and position synchronous belt pulleys without damaging the shaft during installation. Available in a range of materials, including anodized aluminum alloy, polished stainless steel, and black-oxide-finished 45# steel. Bores are machined to H7/H8 tolerances, and custom specifications are available. A variety of sizes are offered, with outer diameters from 16 mm to 85 mm, bore diameters from 3 mm to 50 mm, widths from 8 mm to 22 mm, axial loads from 0.1 to 5.1 kN, and thread sizes from M3 to M10. Their compact design and easy installation make them widely used in automation equipment, transmission systems, and other applications.

DNW Series Split Shaft Collars

DNW Series Split Shaft Collars

The DNW series features split shaft collars made from high-strength aluminum alloy, 45# steel, or stainless steel. Surfaces are anodized (aluminum alloy) or blackened (45# steel). The split design makes installation and maintenance easier, and helps prevent damage when fitting the collar to a shaft. These collars are suitable for shaft retention and timing pulley positioning. Sizes cover outer diameters from 16 mm to 30 mm and inner diameters from 3 mm to 500 mm, with ranges varying by material, to suit a variety of shaft diameters. The standard surface finish is black oxide; zinc plating and phosphating are available as options. Custom specifications are also available.

Shaft Collars

Shaft Collars

Shaft collars, also known as stop collars or limit rings, position and restrain components axially on a shaft. The collar fits over the shaft and is secured with a side set screw or a split-clamp mechanism, preventing bearings, sprockets, pulleys, gears and other components from moving along the shaft. The mounting flange style shown here adds a flange face and mounting holes to the collar, allowing it to be bolted directly to a frame, panel or slide table for easy attachment of stops, sensor brackets, limit switch actuators and other accessories. Common materials include carbon steel with a black oxide or zinc-plated finish, stainless steel and aluminum alloy. Sizes are based on the compatible shaft diameter; when selecting a collar, check the shaft diameter, flange dimensions and mounting hole spacing.

Mounting Flanges

Mounting Flanges

Mounting flanges are accessories for locating nuts (stop rings and shaft collars). They use screws to secure the locating nut axially to a panel, frame, or equipment end face, providing axial positioning, preventing rotation, and ensuring flush mounting. Common materials include carbon steel with a black oxide or zinc-plated finish and stainless steel. Designs include single-slot, double-slot, and raised-boss types, with mounting holes typically countersunk or threaded. When selecting a flange, match it to the bore diameter, outside diameter, and width of the corresponding locating nut, and check the mounting hole center spacing, flange outside diameter, and thickness. This catalog page provides only the title of the mounting flange dimension table; it does not list specific dimensions or model codes. Refer to the selected locating nut's specification page and corresponding drawing for actual dimensions.

ZSCCN Shaft Collars

ZSCCN Shaft Collars

ZSCCN series shaft collars use set screws for secure mounting and are suitable for shafts with diameters from 3 to 50 mm. Materials and finishes include black-oxide-finished S45C steel, nickel plating, SUS304 stainless steel, and natural anodizing for aluminum alloy. Available types include standard, extra-wide, short-hub, and long-hub designs. The set-screw locking mechanism makes installation easy and provides reliable positioning. These collars are widely used in automation equipment, mechanical power transmission, and bearing mounting. A range of precise bore diameters and widths meets diverse application requirements.

ZSCC Set-Screw Shaft Collar

ZSCC Set-Screw Shaft Collar

The ZSCC series set-screw shaft collars are designed for axial positioning of shaft components. Materials include S45C steel (black oxide finish), nickel-plated steel, SUS304 stainless steel, and 2000-series aluminum alloy (clear or black anodized). The bore diameter D ranges from 7 to 53 mm, and the width B ranges from 3 to 18 mm. Available in standard and wide versions. Supplied with two set screws. Commonly used in automation equipment and mechanical drive systems, these collars can be installed and repositioned quickly.

Shaft Collar, Set Screw Type

Shaft Collar, Set Screw Type

Set-screw shaft collars provide axial positioning and locking for shafts, secured by a set screw on the side. The range includes standard and wide types, in materials such as black-oxide S45C, nickel-plated steel, SUS304 stainless steel, and aluminum alloy. Shaft diameters (D) from 7 mm to 53 mm are available, with width (B) selected according to the shaft diameter. For example, order code ZSCCN12-10 specifies a standard type for a 12 mm shaft with a width of 10 mm. Suitable for precision machinery, automation equipment, and other applications.

Set Collars (Set Screw Type)

Set Collars (Set Screw Type)

This series of set collars is secured with set screws and is designed for axial positioning of shaft components. Materials include S45C (black oxide finish), nickel-plated steel, SUS304 stainless steel, and aluminum alloy (anodized finish). Bore diameters range from 3 mm to 18 mm, with widths varying by model. Available in several sizes, including standard (ZSCCN) and wide (ZSCC) types, to meet a variety of application needs. Their simple design makes them easy to install, and they are widely used in automation equipment, mechanical drives, and other applications.

ZSSCN Series Shaft Collars

ZSSCN Series Shaft Collars

The ZSSCN series comprises set-screw shaft collars, available in standard (black-oxide-finished S45C), wide, nickel-plated, stainless steel (SUS304), and aluminum alloy (anodized 2000-series aluminum alloy) versions. These collars provide axial positioning and retention for shafts and are secured with set screws. The diameter D ranges from 3 to 18 mm (see the specifications table on the right), and various widths B are available. For example, the order code ZSCCN12-10 specifies a standard black-oxide-finished S45C shaft collar for a 12 mm shaft, with a width of 10 mm. Two set screws are included as standard accessories. Material and finish vary by model: ZSCCN is black-oxide-finished S45C, ZPSCCN is nickel-plated, ZSSCN is SUS304, and ZSCCA is anodized aluminum alloy. This series is suitable for securing shaft ends in automation equipment and mechanical drive systems.

Set collar, set-screw type

Set collar, set-screw type

This series of split set collars is secured with set screws and is suitable for positioning at shaft ends or providing axial stops. A range of materials and finishes is available to suit different operating environments, including the standard type (black-oxide-finished S45C), wide type, nickel-plated type, SUS304 type, and aluminum alloy type. Order codes consist of a series prefix, inner diameter D, and width B. For example, ZSCCN12-10 denotes a standard type with a 12 mm inner diameter and 10 mm width. Based on the table data, inner diameters range from 7 to 53 mm and widths from 3 to 18 mm. These collars are widely used in mechanical drives and automation equipment.

Shaft Collar, Set-Screw Type

Shaft Collar, Set-Screw Type

This series of set-screw shaft collars is designed to secure components axially on a shaft. The simple, reliable design uses set screws for fastening. Available in a range of materials and finishes: standard and wide types in black-oxide or nickel-plated S45C steel, or SUS304 stainless steel, plus an aluminum-alloy series made from 2000-series aluminum alloy with a natural or black anodized finish. Bore diameters (D) range from 7 mm to 53 mm, and widths (B) from 3 mm to 18 mm; see the specifications table for available combinations. Suitable for a wide range of applications, including automation equipment and mechanical power transmission.

ZSCSM Series Shaft Collars

ZSCSM Series Shaft Collars

This series features split shaft collars in two designs: double-hole fastening and double-thread fastening. Materials include S45C (black oxide finish) and SUS304 (nickel-plated or untreated). Bore diameters D are available from 6 to 12 mm, and widths B from 8 to 12 mm. These collars are used to position and secure shaft components axially. Their simple design makes them easy to install. One hex socket head cap screw is included as standard.

ZPSCSM Series Shaft Collars

ZPSCSM Series Shaft Collars

The ZPSCSM series consists of open-type, two-hole stainless steel shaft collars made of SUS304 and nickel-plated. Each collar comes with one hex socket-head bolt. They are suitable for shaft diameters of 6–40 mm, with width B available in sizes such as 8, 10, and 12 mm, depending on the shaft diameter. The collars are secured with a hex socket-head bolt. Rust- and corrosion-resistant, they are commonly used to position or limit shaft movement in precision machinery and automation equipment.

Shaft Collars (Split Two-Hole Clamping Type / Double-Threaded Type)

Shaft Collars (Split Two-Hole Clamping Type / Double-Threaded Type)

This series of shaft collars is available in two types: split two-hole clamping and double-threaded. Materials and finishes include black-oxide-treated S45C, nickel-plated SUS304, and untreated SUS304. Bore diameters range from 6 to 12 mm, with the width selected according to the bore diameter. These collars are suitable for axial positioning and securing of shafts in mechanical drive systems.

Split Double-Thread Clamping Collar ZSCSW Series

Split Double-Thread Clamping Collar ZSCSW Series

The ZSCSW series features split, double-thread clamping shaft collars made from S45C steel with a black-oxide finish, suitable for securing shafts with diameters of 6–40 mm. The double-thread locking design provides reliable axial retention. Standard widths are 8 mm, 10 mm, and 12 mm, with outer diameters ranging from 20 mm to 80 mm. Each collar comes with one hex socket head bolt. This series is widely used in industrial automation equipment and mechanical drive systems, offering easy installation, accurate positioning, and high load capacity.

Split Shaft Collar, Two-Hole Fastening Type / Dual-Thread Fastening Type

Split Shaft Collar, Two-Hole Fastening Type / Dual-Thread Fastening Type

This series consists of split shaft collars available in two-hole and dual-thread fastening designs. Materials include S45C (black oxide finish) and SUS304 (nickel-plated or untreated). Bore diameters range from 6 to 35 mm, with widths of 8, 10, 12, 15, 20, 25, or 30 mm. These collars are used to position and secure shafts axially, and feature a simple design for easy installation.

Split-Type Clamp Collar, Two-Hole Securing / Dual-Thread Securing

Split-Type Clamp Collar, Two-Hole Securing / Dual-Thread Securing

This series of split-type clamp collars is available in two configurations: two-hole securing and dual-thread securing. Materials include S45C (black oxide finish) and SUS304 (nickel-plated or untreated). They fit shaft diameters of 6, 8, 10, and 12 mm and are available in widths of 8, 10, and 12 mm. Secured with socket-head cap screws, they are easy to install and provide axial positioning on mechanical shafts to prevent movement. The two-hole version is secured through two radial holes, while the dual-thread version locks in place with threaded fasteners, offering different mounting options. Surface finishes include black oxide and nickel plating, providing a degree of rust resistance. Socket-head cap screws are included as standard (stainless steel screws are supplied with SUS304 collars).