Adapter Fittings

MPL/MPM Series Fittings
MPL/MPM series fittings are threaded pipe fittings used for straight connections and transitions between piping components. Models are available in various tube diameters and thread sizes: D is the fitting body diameter (4~16 mm), D1 is the head diameter (8.5~21.5 mm), L is the overall length (28~64.5 mm), L1 is the mating section length (10~24.5 mm), H is the installed height (14~27 mm), and M is the metric fine thread size (M10×1 to M24×1). MPL covers smaller sizes (D4, D6), while MPM covers larger sizes (D8~D16). Select a fitting to match the tube outside diameter and port thread. These fittings are suitable for connecting, adapting and securing tubes and components in pneumatic, hydraulic and instrumentation piping systems. Select materials and seals according to system pressure and media.

RBC Series Thread Adapters
The RBC series consists of pipe thread adapters (reducers) for connecting different thread sizes in pneumatic and fluid lines. Model numbers begin with RBC, followed by two port codes indicating the thread size at each end. For example, RBC-G01-G02 has a G1/8 thread at one end and a G1/4 thread at the other. The catalog covers G1/8, G1/4, G3/8, G1/2 and G3/4 port sizes (corresponding to codes G01, G02, G03, G04 and G06) and lists combinations of G (parallel female/male pipe threads) and R (tapered pipe threads). Key dimensions include overall length L (approximately 13.5~31.5 mm), effective lengths L1/L2 at each end (approximately 5.5~18 mm), and width across flats H (14~32 mm). Select a model based on available piping and wrench clearance. Both same-size configurations (G01-G01, G02-G02, etc.) and reducing configurations (G01-G02, G02-G03, G03-G04, G04-G06, etc.) are available.

RA Type Male-Female Adapter
The RA type male-female adapter is a straight transition fitting with a male thread at one end and a female thread at the other. It connects different thread sizes in pneumatic, hydraulic and fluid lines. Thread sizes include PT/NPT 1/8, 1/4, 3/8, 1/2, 3/4 and 1. Model numbers consist of RA followed by the thread codes for both ends (e.g., RA-01-01). Key dimensions are overall length A, minimum bore E and hex width across flats F. A is approximately 27~49mm, the minimum bore is 5~15mm, and the width across flats is 14~40mm. The fitting is typically made of brass. The same catalog page also lists RHCG type female-threaded couplings and female-threaded reducing elbows, which have different configurations and are not part of this series.

RHCG Female-to-Male Threaded Adapter
The RHCG female-to-male threaded adapter connects piping with different thread sizes at the female (P) and male PT/NPT ends. It is suitable for hydraulic, pneumatic and general industrial piping systems. The catalog lists RHCG-01, RHCG-02, RHCG-03, RHCG-04, RHCG-06 and RHCG-08 models. P thread sizes range from 1/8 to 1, male PT/NPT thread sizes from 1/8 to 1/4, dimension A from 25 to 49 mm, minimum bore E from 8 to 29 mm, and hex width across flats F from 14 to 40 mm. Select the model based on the thread sizes at both ends and the available installation space.

RHCG Series Female Reducing Elbow Adapters
The RHCG female reducing elbow adapter connects two threaded pipes at a 90° angle. Both ends have female threads, making it suitable for adapting threaded connections in pneumatic, hydraulic and general piping systems. The catalog specifies P-end thread sizes of 1/4~1 inches and mating-end PT/NPT sizes of 1/8~3/4 inches, along with overall length A of 32~49 mm, minimum bore E of 8~23 mm and hex width across flats F of 17~40 mm. The product code consists of RHCG followed by two two-digit segments: the first identifies the P-end thread size (02=1/4, 03=3/8, 04=1/2, 06=3/4, 08=1), and the second identifies the thread size at the other end (01=1/8, 02=1/4, 03=3/8, 04=1/2, 06=3/4). The same page also lists similar products, including RA male-to-female adapters and RHCG female couplings. Select the fitting to match the thread sizes at both ends.

Transition Fittings
Transition fittings connect and adapt different thread sizes, thread types (PT/NPT), or male and female threads in piping systems. They are commonly used in pneumatic, hydraulic, and fluid lines. This series includes RB reducing bushings (male-to-female connections of different sizes), MET male elbows, E female elbows, SE male-to-female elbows, T female tees, and MT male tees. Six thread sizes are available: 1/8, 1/4, 3/8, 1/2, 3/4, and 1. Model numbers consist of a type code and a size code, such as RB-02-01, MET-02, E-02, SE-02, T-02, and MT-02. Selection parameters include the thread sizes at both ends, overall dimensions, minimum bore, and width across flats. Choose according to the pipe bore and available installation space. Materials and surface finishes depend on the supplied specifications.

RB Type Reducing Nipple
The RB type reducing nipple is a male-to-male reducing adapter with PT/NPT male threads at both ends. It directly connects different pipe thread sizes, providing transitions from 1/8 to 1 inch. The catalog lists 13 common sizes, from RB-02-01 to RB-08-06, by P and P1 end combinations. It also specifies overall length E (20~35 mm), minimum bore F (7~22 mm), and hex width across flats (14~35 mm) to aid selection and installation. The product is suitable for reducing connections in pneumatic, hydraulic, and general fluid piping systems.

MET Series Male Elbows
The MET male elbow is an adapter fitting for 90° turns in piping, with PT/NPT male threads at both ends (MALE×MALE, double male). The catalog lists six thread sizes—1/8, 1/4, 3/8, 1/2, 3/4, and 1—corresponding to models MET-01, MET-02, MET-03, MET-04, MET-06, and MET-08. The last two digits of the model number increase with thread size. Key dimensions include the thread sizes P/P1 at both ends, opening size E (5~21mm), and width across flats S (19.8~45.2mm). Select the model according to the pipe thread size, then check the opening and width across flats against the available installation space. This series can be combined with other adapter fittings on the same catalog page, including RB bushings, E female elbows, SE male-female elbows, T female tees, and MT male tees, to form a complete piping connection solution.

E-Type Female Elbow
The E-type female elbow is an adapter fitting used to connect two pipe sections at a right angle. Both ends have female PT/NPT threads. The catalog lists models E-01, E-02, E-03, E-04, E-06, and E-08 in nominal sizes of 1/8, 1/4, 3/8, 1/2, 3/4, and 1 inch, respectively, with different E dimensions and L lengths. The fitting is suitable for pneumatic, hydraulic, and general industrial piping. Select the appropriate thread size for installation, and ensure proper sealing and tightening torque. Dimensions in the table are in mm, and thread types are PT/NPT.

SE Series Male-to-Female Threaded Elbow
The SE series male-to-female threaded elbow is a 90° adapter with a male thread on one end and a female thread on the other. It changes the direction of air, water, oil, and other fluid lines while providing a threaded transition. The series is available in six thread sizes: 1/8, 1/4, 3/8, 1/2, 3/4, and 1, corresponding to models SE-01, SE-02, SE-03, SE-04, SE-06, and SE-08. The catalog lists E (bore), L (length), and S (hex across flats) dimensions for each size to facilitate selection and space checks. Compact and easy to install, these elbows are suitable for factory automation pneumatic systems and general-purpose fluid lines.

T Series Female Tee Transition Fittings
The T series female tee is a transition fitting with three female-threaded ports, used to split one pipeline into two. It is commonly used in air, water, oil and other fluid systems. The fittings have PT/NPT tapered pipe threads and are available in six nominal sizes: 1/8, 1/4, 3/8, 1/2, 3/4 and 1, corresponding to models T-01, T-02, T-03, T-04, T-06 and T-08. The catalog specifies three dimensions: A (overall length), E (distance from the threaded end face to the center of the tee/opening size) and L (center length). For example, T-01 has A = 40.0mm, E = 8mm and L = 20.0mm, while T-08 has A = 94.4mm, E = 29mm and L = 47.2mm. When selecting a fitting, first determine the nominal size and model based on the pipeline thread specification, then check that the A/E/L dimensions fit the available installation space. Combined with transition fittings on the same page, such as elbows (E type and SE type), male tees (MT type) and reducing bushings (RB type), they can form

MT Male Threaded Tee
The MT male threaded tee is an adapter fitting with PT/NPT male threads on all three ports. It is used to split or combine flows in pneumatic or fluid piping systems. The catalog offers six thread sizes—1/8, 1/4, 3/8, 1/2, 3/4 and 1—corresponding to MT-01, MT-02, MT-03, MT-04, MT-06 and MT-08. Depending on the size, overall dimension A ranges from 39.6~90.4 mm, opening E from 5~21 mm and length L from 19.8~45.2 mm, making it easy to select a fitting for the available space and flow requirements. This standard adapter is suitable for equipment piping and maintenance replacement.

BZ/BP/BP-G Series Adapter Fittings
The adapter fitting series includes three types: BZ external hex, BP internal hex, and BP-G internal hex with G threads. They provide threaded transitions and connections in pneumatic and fluid lines. BZ models have an external hex design and are available in sizes 1/8~3/4; BP models have an internal hex design and are available in sizes 1/8~3/4; BP-G models have an internal hex design with G (parallel) threads and are available in sizes G1/8~G3/4. Dimensions including width across flats A, hex height H, and overall length L are provided for each size to simplify selection and installation. These fittings are widely used to connect lines in compressed air and pneumatic systems.

PHF Series Inline Connectors
PHF series inline connectors are straight male-to-female threaded adapters for pneumatic and fluid lines. One end has a male thread (M5, R or NPT) and the other a female thread (M5, Rc or NPT). They are used to extend lines, adapt threaded connections or connect components with different thread sizes in series. The standard PHF series fits tube diameters ΦD 4~12mm, with threads including M5, R1/8~R1/2 and Rc1/8~Rc1/2. The PHF-N series is the imperial NPT-threaded version, fitting tube diameters 5/32~1/2in with threads from NPT1/8~NPT1/2. The catalog specifies four lengths, L1, L2, L3 and L4, the ΦD1 outside diameter and the φ hex width across flats to facilitate installation space checks. The compact connectors are suitable for factory automation pneumatic circuits, fixtures, jigs and general industrial fluid lines.

PHF-N Series Inline Fittings (NPT Thread)
PHF-N series inline fittings are straight push-in fittings for inch-size pneumatic tubing. They have an NPT male thread (R) at one end and an NPT female thread (Rc) at the other, for straight connections, transitions or panel-mounted connections between two pneumatic lines. Compatible tube outside diameters are 5/32, 3/16, 1/4, 5/16, 3/8 and 1/2 inches. Four thread sizes are available: NPT1/8, NPT1/4, NPT3/8 and NPT1/2, with 14 standard models in total. Key dimensions include tube diameter ΦD, male/female thread size R/Rc, thread length L1, effective thread engagement length L2, overall length L3 (29~47.5 mm), insertion end length L4, body outside diameter ΦD1 (11.5~21.5 mm) and hex width across flats φ, for checking installation clearance and selecting a wrench. The model code combines the series designation PHF, the tube diameter as an inch fraction and the NPT thread size code (N01~N04).

KQ2ZF Double-Ended Male-to-Female Threaded Fitting
The KQ2ZF double-ended male-to-female threaded fitting is part of the KQ2 series of push-to-connect pneumatic fittings. It provides a threaded transition in pneumatic circuits: one end has a male thread that screws directly into a female-threaded component, such as a cylinder, valve or manifold; the other has a female thread for connection to a male-threaded component. The fitting body is generally made of nickel-plated brass. Its collet-style push-to-connect mechanism allows nylon and PU tubing to be inserted and locked in place or quickly removed without tools. The threaded section is usually precoated with sealant, eliminating the need for thread seal tape. Available tubing outside diameters are 4, 6, 8, 10, 12 and 16 mm. Connection threads include M5×0.8, M6×1.0 and tapered pipe threads such as 1/8(01S), 1/4(02S), 3/8(03S) and 1/2(04S). The hexagon width across flats varies with the thread size for convenient tightening with a wrench. The same series also includes the double-ended external hexagon KQ2Z, double-ended internal hexagon KQ2ZS, single-end 2-group KQ2VD, single-end 3-group KQ2VT and single-sided KQ2C variants, which can be combined into a complete pneumatic piping solution.