Check Valves

FSPC Series Check Valves

FSPC Series Check Valves

FSPC series check valves are used in pneumatic circuits to allow compressed air to flow in one direction only, preventing reverse flow. They are commonly used wherever one-way airflow is required. The operating medium is air only; other gases and liquids must not be used. The operating pressure range is 0.05~1.0MPa (150psi). Models are classified by nominal bore and include FSPC04, FSPC06, FSPC08 and FSPC10. Port threads include G1/8, G1/4, G3/8, R1/8, R1/4, R3/8 and R1/2. Dimensions (ΦD, ΦD1, L1, L2, L3, Φp, L) vary by model. During installation, tighten the screws to the specified torque. Overtightening may cause the valve to malfunction.

CV Series Check Valves

CV Series Check Valves

The CV series consists of inline pneumatic check valves that allow airflow in one direction and prevent reverse flow. They are commonly installed in circuits between cylinders, air preparation components, and directional control valves. The straight-through valve body uses an internal valve element and spring to open in the forward direction and seal against reverse flow. During installation, observe the airflow direction arrow marked on the valve body. The model code has three parts: series code CV + two-digit port size code + thread type code. Eight port sizes are available: 06(1/8″), 08(1/4″), 10(3/8″), 15(1/2″), 20(3/4″), 25(1″), 40(1-1/2″), and 50(2″), accommodating pneumatic lines from small-diameter tubing to high-flow main lines. Thread type codes are blank (PT thread), G(G thread), and T(NPT thread), corresponding to regional thread standards for compatibility with piping in different countries. Select the port size and thread type codes according to the connected line's internal diameter and thread standard.

KA Series Check Valves

KA Series Check Valves

KA series check valves are directional control components that allow airflow in one direction and prevent reverse flow in pneumatic systems. The working medium is air filtered through a 40μm or finer filter. The operating pressure range is 0.15~0.8MPa (21~114psi), the proof pressure is 1.5MPa, and the operating temperature range is -20~70℃. The series includes 6 sizes, with connection ports from G1/8 to G1 and effective areas of 10~190mm² that increase with port size to suit pneumatic circuits with different flow requirements. The valves have threaded connections, a compact design, and are easy to install. They can be used with cylinders, solenoid valves, and other pneumatic components.

PCV Series Check Valves

PCV Series Check Valves

PCV series check valves (one-way valves) maintain pressure and form safety circuits in pneumatic systems. They prevent reverse airflow, allowing cylinders to stop instantly and achieve precise positioning. The valves feature a special circuit design and are available with a push-in pilot port (F type) to save installation space and improve installation efficiency. The working medium is air filtered to 40μm or better. Operating pressure is 0.1~1.0MPa, proof pressure is 1.5MPa, operating temperature is -20~70℃, and operating frequency is 40 cycles/min. Body size is 24.5mm, connection sizes range from PT1/8~PT1/2, and the pilot port is M5×0.8 or 1/8"~1/4". The ordering code consists of PCV and the specification code.

NRV Series Check Valves

NRV Series Check Valves

The NRV series comprises in-line pneumatic check valves (one-way valves) that control airflow in one direction and prevent backflow. They are used in pressure-holding safety circuits and for precise locking when cylinders stop instantaneously. The standard range includes six models: NRV06, NRV08, NRV10, NRV15, NRV20 and NRV25, with respective port sizes of PT1/8, PT1/4, PT3/8, PT1/2, PT3/4 and PT1. Effective areas range from 18~250 mm², with corresponding Cv values of 1.0~14.44, covering low- to high-flow pneumatic circuits. The working medium is air filtered through a 40μm or finer filter. The operating pressure range is 0.02~1.0MPa (2.9~145psi), the proof pressure is 1.5MPa (215psi), and the operating temperature is -20~70℃. The aluminum alloy body is lightweight and easy to install. In addition to standard PT threads, G and NPT threads are available to suit piping connections in different countries and regions.