Standard Cylinder

C95 Series European Standard Cylinders

C95 Series European Standard Cylinders

The C95 series is a range of double-acting cylinders conforming to the European standard ISO 15552, with ten bore sizes: 32, 40, 50, 63, 80, 100, 125, 160, 200 and 250 mm. Operating on compressed air at pressures from 0.05 MPa to 1.0 MPa, they are suitable for common automation tasks such as pushing, pulling, clamping and positioning. The cylinder barrel is made from extruded aluminum alloy, and the end caps are connected to the barrel by tie rods. Overall and mounting dimensions conform to European standards, allowing the use of compatible mounting accessories such as foot brackets, flanges and clevises, as well as magnetic switches. The standard model is C95S, and users can select a configuration based on the mounting method and required stroke. The catalog also provides overall and mounting dimensions including A, AA, B, C, CC, CD, CJ, D, E, F, G, H, I, K and L for preparing installation drawings.

CA2 Series Standard Cylinder

CA2 Series Standard Cylinder

The CA2 series is a standard pneumatic cylinder listed in the catalog as “CA2: Basic type.” It is suitable for linear pushing and pulling, clamping, positioning, and similar applications in automated equipment. The table lists common bore sizes of 32, 40, 50, 63, 75, 100, and 125 mm, and stroke lengths of 10, 20, 30, 40, 50, 75, 100, and 125 mm. Configuration options include blank: no adjustment, blank: no cushioning, and blank: basic type. The table on this page covers multiple series; the complete CA2 ordering codes and accessory combinations should be confirmed against the relevant ordering catalog.

CA2 Series Standard Cylinders

CA2 Series Standard Cylinders

CA2 series standard cylinders are double-acting pneumatic actuators with JIS-standard mounting dimensions, available in five bore sizes: 40, 50, 63, 80 and 100 mm. They have an operating pressure range of 0.05~1.0 MPa, an operating speed of 50~500 mm/s and an ambient temperature range of -10℃~+70℃. Mounting options include basic, flange, single clevis, double clevis and center trunnion types, allowing direct replacement and installation in multiple orientations. The compatible cast-iron trunnion brackets have part numbers CA2-L04, CA2-L05, CA2-L06, CA2-L08 and CA2-L10, corresponding to bore sizes of 40, 50, 63, 80 and 100 mm, respectively. Bracket dimensions increase with bore size, with mounting dimensions such as CD, U, L, RR and CX increasing accordingly. Catalog illustrations are for reference; trunnion brackets must be ordered separately. The series is widely used for linear pushing and pulling, clamping and lifting in automated assembly lines, fixture positioning and material handling.

SCF Series Standard Cylinder with Valve

SCF Series Standard Cylinder with Valve

This series combines a standard cylinder with a valve and is designed for use with 4M210 and 4M310 valves. Bore sizes 32, 40, and 50 use the 4M210 valve; bore sizes 63, 80, and 100 use the 4M310 valve. One-to-one control eliminates the need for a separate control valve. The series is suitable for distributed use in large systems, and a range of mounting accessories is available. Two operating modes are available: the piston rod can retract or extend when energized. The factory default is for the piston rod to retract when energized. To change this to extension when energized, remove the solenoid valve and reinstall it in the opposite orientation. When removing or installing the solenoid valve, ensure that the sealing O-ring between the valve and the connecting block is in the correct position.

SU Series Standard Cylinders

SU Series Standard Cylinders

CG1 Series Light-Duty Pneumatic Cylinder

CG1 Series Light-Duty Pneumatic Cylinder

The CG1 series light-duty cylinder is a single-rod pneumatic actuator with an aluminum alloy profile body and rubber cushioning. Compact, lightweight, fast-responding and easy to install, it is widely used for light-load pushing, clamping, lifting and positioning in automated equipment. The series includes CG1 (without built-in magnetic ring) and CDG1 (with built-in magnetic ring) versions. Magnetic switches can be fitted in the CDG1 cylinder body's grooves to detect extended and retracted positions. Bore sizes are 20, 25, 32, 40, 50, 63, 80 and 100 mm, with stroke lengths selected to suit the application. Mounting options include B basic, L axial, F rod-side flange, G non-rod-side flange, U rod-side trunnion, T non-rod-side trunnion and D clevis. Protective covers and magnetic switches such as B54 are also available. In the model code, N means no grease/rubber cushioning. The operating medium is purified compressed air containing oil mist.

CG1BN Series Lightweight Aluminum Alloy Cylinder

CG1BN Series Lightweight Aluminum Alloy Cylinder

The CG1BN series is a lightweight aluminum alloy cylinder designed for linear reciprocating motion in factory automation equipment. The catalog lists multiple bore and stroke combinations under the CG1BN model, making it easy to select the right configuration for the available space and load requirements. The aluminum alloy body reduces weight, making it suitable for pneumatic applications where weight and mounting space are important considerations. Available variants include female rod threads, non-standard strokes, non-rotating rods, -S/-T, double-rod, adjustable, and RN square-head mounting types. Different variants may incur additional charges or require a quotation. Confirm the specific bore, stroke, and ordering combinations in the catalog tables.

CP95 Series Square-Body Cylinder

CP95 Series Square-Body Cylinder

The CP95 series is a European-standard square-body cylinder with mounting provisions on multiple sides for easy direct installation or attachment of accessories in automated equipment. An optional built-in magnet works with magnetic switches to detect piston position. Mounting options include the basic type and various mounting codes (B/L/F/G, etc.). Model numbers combine the CP95 series code, type code, built-in magnet code, mounting style, bore, stroke, and accessory code. For example, CP95SDB32-100Z73 has a 32 mm bore, 100 mm stroke, and Z73 accessory. These cylinders are commonly used for linear push-pull, clamping, positioning, and stopping applications.

CP96 Series European Standard Cylinders

CP96 Series European Standard Cylinders

The CP96 series consists of double-acting cylinders built to the European standard ISO 15552, with seven bore sizes: 32, 40, 50, 63, 80, 100 and 125 mm. They are suitable for linear pushing and pulling, clamping, lifting and positioning in general industrial automation. Their mounting dimensions conform to European standards, allowing interchangeable installation with standard accessories of matching specifications, such as foot mounts, flanges and clevises. Three basic mounting styles are available: foot mount (code L), flange mount (code F) and single clevis mount (code C). Compatible mounting accessories support horizontal, vertical or pivoting installation. The main selection parameters are bore size, stroke and mounting style. Other common specifications, including action type, operating flow rate, proof pressure, maximum operating pressure and minimum operating pressure, are specified by bore size. With a simple design, easy maintenance and broad versatility, these cylinders are commonly used as actuators on factory automation lines. For specific stroke ranges and pressure ratings, refer to the specification tables in the manufacturer's catalog.

CS1 Series Standard Cylinders

CS1 Series Standard Cylinders

CS1 series standard cylinders (medium-to-large bore type) are double-acting and suitable for general industrial pneumatic applications. An air-oil version is also available; the pneumatic version uses air as its working medium, while the air-oil version uses turbine oil. The 13 bore sizes range from Φ32 to Φ300 mm: 32, 40, 50, 63, 80, 100, 125, 140, 160, 180, 200, 250 and 300 mm, providing a range of low-to-high thrust outputs. Maximum operating pressure is 0.9 MPa, and minimum operating pressure is 0.05 MPa (0.06 MPa for the air-oil version). Piston speed is 50~500 mm/s, or 0.5~200 mm/s for the air-oil version. The operating temperature range is 0~70 ℃ (5~60 ℃ for the air-oil version); prevent moisture from freezing at low temperatures. The catalog also provides overall and mounting dimensions for each bore size (A, AA, B, C, CC, CD, CJ, D, E, F, H, I, J, K, L, N, O and N+O+90°, among others) to support product selection, calculations and installation design. These cylinders are widely used in automated applications such as fixture clamping, workpiece pushing and valve actuation.

HTK Series

HTK Series

The HTK Series comprises standard double-acting cylinders with aluminum alloy bodies treated with an anodized coating for wear and corrosion resistance. Oil-free bearings and wear-resistant sealing rings provide a long service life. Multiple port positions are available. The cushioned version reduces impact, while the version with a magnetic ring can be used with reed switches. Available bore diameters are 40, 50, and 63 mm, with strokes from 50 to 150 mm in 25 mm increments. Operating pressure: 0.5–9.9 kgf/cm². Speed range: 50–500 mm/s. Cushioning: adjustable cushioning at the end positions. Optional configurations include adjustable air intake (A) and a built-in magnet (M).

HLC-FAM Series Standard Cylinders

HLC-FAM Series Standard Cylinders

The HLC-FAM series comprises standard cylinders commonly used in factory automation and includes two subseries: HLC-FAM and HLC-FAMT. It is available in six bore sizes ranging from 25 to 63 (with actual cylinder barrel outside diameters of 45 to 81 mm), along with detailed mounting dimensions, including piston rod diameters, mounting-hole spacing, and thread sizes. The series features O-ring seals and a compact design, making it suitable for a wide range of pneumatic actuators.

SC Series Standard Cylinders

SC Series Standard Cylinders

SC Series standard cylinders are designed with large bore sizes of 125 mm, 160 mm, 200 mm, and 250 mm, making them suitable for pneumatic applications requiring greater thrust. They use compressed air filtered through a filter rated at 40 μm or finer and feature double-acting operation. With their reliable construction, these cylinders are widely used in automation equipment, industrial machinery, and other applications.

SC Series Standard Cylinder

SC Series Standard Cylinder

The SC series standard cylinder (concealed tie-rod type) features an aluminum alloy barrel and concealed tie rods for linear reciprocating motion in automated equipment. Bore sizes include 32, 40, 50, 63, 80, and 100 mm, with stroke lengths from 10~100 mm available. The model code specifies, in order, the series number, bore, stroke, adjustable stroke (N adjustable stroke distance / S with magnet), magnet code (S with magnet, blank without magnet), and mounting type (basic type, CA rear single clevis, CB rear double clevis, FA front flange, FB rear flange, LB foot mounting, TC pivot mounting, TC-M pivot mounting with foot bracket). Multiple variants are available, including standard double-acting, double-rod, adjustable double-rod, and multi-position types, with flexible mounting options.

SI Series Standard Cylinders

SI Series Standard Cylinders

SI series standard cylinders feature concealed tie rods and are available in standard, double-rod, adjustable double-rod, and multi-position configurations. Bore sizes range from 32~100mm, and the stroke can be selected to suit the application. Options include an adjustable stroke (N), a built-in magnet (S), and various mounting styles, such as FA front flange, CA single clevis, CB double clevis, LB foot mount, and TC trunnion mount. Compact and easy to install, these cylinders provide pneumatic actuation for a wide range of automated equipment.

DNC/SE Series Standard Cylinders

DNC/SE Series Standard Cylinders

DNC/SE series standard cylinders are general-purpose, double-acting cylinders with mounting dimensions compliant with the ISO6431 international standard. Bore sizes include 32, 40, 50, 63, 80, 100 and 125 mm, with common stroke lengths of 10, 20, 30, 40, 50, 75, 100 and 125 mm to meet most linear push-pull requirements. The cylinders feature an aluminum alloy barrel and concealed tie rods for a compact design. Standard mounting holes allow interchangeable installation with a wide range of international standard cylinders. An optional built-in magnetic ring (MDB type) enables position detection with magnetic switches. Mounting accessories include SNCB double-clevis mounts, single-clevis mounts and HNC foot mounts, supporting flange, foot, clevis and pivoting configurations. Pneumatic cushioning (PPV) reduces impact and noise at the end of the stroke, while the adjustable stroke (N) option provides mechanical travel limiting for certain applications. These cylinders are widely used in automated assembly lines, packaging machinery, tooling and fixtures, and material handling.

MBB Series Standard Cylinders

MBB Series Standard Cylinders

MBB series standard cylinders are tie-rod cylinders suitable for linear pushing and pulling, clamping, lifting, and other industrial automation applications. The catalog includes the basic MBB model and the MDBB model with a built-in magnetic ring. Common bore sizes are 32, 40, 50, 63, 80, 100, and 125 mm, with stroke options including 10, 20, 30, 40, 50, 75, 100, 125, and 150 mm. Adjustable stroke, a built-in magnet, and mounting styles such as FA/FB/CA/CB/LB/TC/TC-M can be selected as needed. An example model code is MBB 50×150-N S FA.

SC Series Standard Cylinders

SC Series Standard Cylinders

SC series standard cylinders are general-purpose, double-acting tie-rod cylinders with square aluminum bodies. They are among the most widely used basic actuators in factory automation, serving applications such as clamping, pushing, lifting, stopping and transferring. The cylinder body is typically made from extruded aluminum alloy, with four tie rods connecting the end caps to the barrel. This simple design makes maintenance easy. Piston rods are generally made of hard chrome-plated carbon steel or stainless steel, with wear-resistant nitrile rubber seals. The main selection criteria are bore size (commonly φ32, φ40, φ50, φ63, φ80 and φ100), stroke and mounting style (basic, front/rear flange, foot, clevis, etc.). Magnetic switches can be added for position detection, and some models support adjustable cushioning and air cushioning. This catalog page provides only a blank framework for the stroke-to-specification table and does not list specific bore sizes, stroke values or complete model codes. Actual specifications should be checked against other pages of the full catalog or confirmed with the manufacturer.

HSU Series Standard Cylinders

HSU Series Standard Cylinders

HSU series standard cylinders feature concealed tie rods and are available in 32, 40, and 50 mm bore sizes. Configurations include standard (concealed tie-rod), double-rod, and double-rod with adjustable stroke. Mounting options include basic, CA rear cap mount (single clevis), CB rear cap mount (double clevis), FA front cap mount (front flange), FB rear cap mount (rear flange), TC intermediate trunnion mount, and TCM1 intermediate trunnion mount (for intermediate mounting). Cylinders are available with or without a magnet. Seal materials include TPU, fluororubber, NBR, and PTF, and port threads are available in G or NPT. They are suitable for automated equipment requiring linear reciprocating motion with a standard stroke.

HSE Series Standard Cylinders

HSE Series Standard Cylinders

The HSE series comprises standard pneumatic cylinders designed for general-purpose actuation. They convert compressed air pressure into reciprocating linear motion and are widely used for pushing, clamping, lifting, conveying, and positioning in automated equipment. The catalog uses a model code structured as “series code + bore + stroke + mounting type”: the series code identifies the product family (HSE), the bore determines the output force and body cross-sectional dimensions, the stroke determines the effective working length, and the mounting type determines the installation method, such as basic, front flange, rear flange, foot, or clevis mounting. When selecting a cylinder, first choose the bore based on the load and required force, then determine the stroke based on the actual travel distance, and finally select the mounting type according to the available installation space and direction of force. Suitable mounting accessories and sensing devices, such as magnetic switches, can also be used. This page provides a series overview and model code explanation; see subsequent pages for bore specifications, stroke tables, and external dimensions.

HGGA/HGGB Series Standard Cylinders

HGGA/HGGB Series Standard Cylinders

HGGA/HGGB series standard cylinders are general-purpose, double-acting linear cylinders. The HGGA is uncushioned, while the HGGB is cushioned. Available bore sizes are 63, 80, 100, 125, 160, 180 and 200 mm, with stroke lengths of 250, 320, 400, 500, 600 and 800 mm. When ordering, specify the magnetic ring designation as needed (a blank indicates no internal magnetic ring). One to three optional magnetic switches can be fitted to detect end-of-stroke positions and provide feedback signals. The cushioned model incorporates cushioning at the ends of the stroke to absorb impact, reduce operating noise and extend cylinder life. Compact and easy to install, these cylinders are widely used for reciprocating linear movements in automation equipment, including pushing, lifting, clamping, positioning and transfer. They can be combined with solenoid valves, air preparation units and magnetic switches to form a complete pneumatic control system.

SC Series Standard Cylinders

SC Series Standard Cylinders

SC series standard cylinders are available in six bore sizes: 32, 40, 50, 63, 80 and 100 mm. The two main types are the SC basic type and the SCD double-rod type. The cylinder body and front cover are made of aluminum alloy, the piston rod is ground S45C carbon steel, the seals are NBR and TPU, and the threaded bushing is made of wear-resistant material. The compact design provides durability and wear resistance. Bore sizes from 32~100 mm use air inlet port threads of PT1/8, PT1/4, PT3/8 or PT1/2, and piston rod end threads range from M10×1.25 to M20×1.5. A magnetic version is available for position detection with magnetic switches. Magnetic and non-magnetic versions have identical external and mounting dimensions for easy interchangeability. The catalog also provides the full range of A, AB, AC, AD, AE, B, D, DA, E, EA, F, FA, H, K, KA, KB, M, MA, P, PA and PB dimensions for each bore size, for use in mounting hole layout and product selection. These cylinders are commonly combined with solenoid valves, connection blocks, APC/APH fittings and PU tubing to form a complete pneumatic actuation circuit.

SCD Series Standard Cylinder

SCD Series Standard Cylinder

The SCD series standard cylinder is a pneumatic actuator with an aluminum alloy cylinder body, a ground S45C carbon steel piston rod, and aluminum alloy front and rear covers. Its seals are made of NBR/TPU, and its wear components are made of wear-resistant materials. It is suitable for linear push-pull, clamping, lifting, and similar applications in automated equipment. Standard bore sizes are 32, 40, 50, 63, 80, and 100 mm. Magnetic and non-magnetic versions have identical mounting dimensions. The external specification table lists mounting and connection parameters including A, AB, AC, AD, AE, B, D, DA, E, EA, F, FA, H, K, KA, KB, M, MA, P, PA, and PB. Port sizes range from PT1/8 to PT1/2. Various mounting configurations are available (SC, SCD).

SC Series Standard Cylinders (Large Bore)

SC Series Standard Cylinders (Large Bore)

SC series large-bore standard cylinders feature an aluminum alloy barrel and end caps, an S45C hardened piston rod, and NBR/TPU seals. Their square, four-tie-rod construction provides high rigidity and resistance to off-center loads, making them suitable for high-force, heavy-duty linear pushing, lifting, and clamping applications. The catalog lists four bore sizes: 125, 160, 200, and 250 mm. Three mounting types are available: SC (basic type), SCD, and SCJ. Select a model based on the mounting method and required stroke. The model number generally combines the mounting type code, bore, and stroke (e.g., SC125×100). The exposed end of the piston rod is threaded for direct connection to various fittings, floating joints, and fixtures. These cylinders are widely used in packaging, assembly, stamping, welding fixtures, and custom automation equipment.

SG/SGC Series Double-Acting Cylinders

SG/SGC Series Double-Acting Cylinders

The SG/SGC series consists of double-acting, tie-rod pneumatic cylinders with standard bore sizes of 125, 160, 200, and 250 mm. The working medium is compressed air filtered through a 40μm or larger filter screen. The operating pressure range is 0.15~1.0 MPa (22~145 psi / 1.5~10.0 bar), with a proof pressure of 1.5 MPa (21 psi / 15 bar). The operating temperature is -20~70℃, the operating speed range is 30~500 mm/s, and the stroke tolerance range is 0~250 mm. A wide range of mounting configurations is available: SG and SGC cylinders can be supplied in basic, FA, FB, CA, CB, CR, LB, TC, FCT, TCM1, or TCM2 configurations; SGD, SGCD, SGJ, and SGCJ cylinders can be supplied in basic, FA, LB, TC, FCT, TCM1, or TCM2 configurations. Flanges, foot mounts, trunnions, and other accessories are available to suit the bore size. Components include nuts, clevis rods, front and rear covers, threaded sleeves, clevises, socket head bolts, tie rods, and tie-rod nuts. Magnetic and non-magnetic versions have identical mounting dimensions, making it easy to add position sensing switches.

SGD Series Cylinders

SGD Series Cylinders

The SGD series consists of standard double-acting cylinders available in several body styles, including SG, SGC, SGD, SGCD, SGJ and SGCJ. This page covers four large bore sizes: 125, 160, 200 and 250mm. The working medium is compressed air filtered through a 40μm or finer filter. The operating pressure range is 0.15~1.0MPa (22~145psi / 1.5~10.0bar), proof pressure is 1.5MPa (21psi / 15bar), operating temperature is -20~70℃, operating speed range is 30~500mm/s, and stroke tolerance range is 0~250. All models are double-acting, with an adjustable double-acting option for applications requiring end-of-stroke cushioning and fine position adjustment. A wide range of mounting options is available: SG and SGC series support basic, FA, FB, CA, CB, CR, LB, TC, FCT, TCM1 and TCM2 mounts; SGD, SGCD, SGJ and SGCJ series support basic, FA, LB, TC, FCT, TCM1 and TCM2 mounts. Magnetic and non-magnetic versions have identical external and mounting dimensions, allowing direct interchangeability and

SGCD Series Standard Cylinder

SGCD Series Standard Cylinder

The SGCD series is a double-acting standard cylinder available in 125, 160, 200, and 250 mm bore sizes. Its working medium is air filtered through a filter rated 40μm or higher. It has an operating pressure of 0.15~1.0 MPa, a pressure resistance of 1.5 MPa, an operating temperature range of -20~70℃, and an operating speed of 30~500 mm/s. SGD, SGCD, SGJ, and SGCJ types are available with basic, FA, LB, TC, FCT, TCM1, TCM2, and other mounting options; SG and SGC also offer FB, CA, CB, CR, and other mounting options. Cylinder components include the front cover, rear cover, sleeved rod, nut, threaded sleeve, and seals. Magnetic and non-magnetic versions have identical mounting dimensions.

SGJ Series Cylinders

SGJ Series Cylinders

The SGJ series consists of double-acting cylinders for pneumatic systems using air filtered through a 40μm or larger filter. The standard specifications on this page cover bore sizes of 125, 160, 200, and 250 mm, a working pressure range of 0.15~1.0 MPa (22~145 psi / 1.5~10.0 bar), a pressure resistance of 1.5 MPa, an operating temperature of -20~70℃, an operating speed range of 30~500 mm/s, and a stroke tolerance range of 0~250. SGJ cylinders are available in a basic configuration and with FA, LB, TC, FCT, TCM1, and TCM2 mounting options. Magnetic and non-magnetic versions have the same dimensions. They are suitable for pushing, pulling, clamping, positioning, and other general industrial automation applications.

SGCJ Series Cylinders

SGCJ Series Cylinders

The SGCJ series consists of double-acting cylinders with standard catalog bore sizes of 125, 160, 200, and 250 mm. The working medium is air filtered through a 40 μm or larger filter. The operating pressure range is 0.15~1.0 MPa, pressure resistance is 1.5 MPa, operating temperature is -20~70 ℃, operating speed range is 30~500 mm/s, and stroke tolerance range is 0~250 mm. SGCJ mounting options include basic, FA, LB, TC, FCT, TCM1, and TCM2, making the cylinders suitable for linear reciprocating motion, clamping, and pushing applications in factory automation equipment.

MBB Series Standard Cylinders

MBB Series Standard Cylinders

The MBB series of standard cylinders includes the basic MBB model and variants such as MBBD and MBBJ, with seven bore sizes: 32, 40, 50, 63, 80, 100 and 125 mm. The operating medium is compressed air filtered through a 40μm filter. Operating pressure is 0.1~1.0MPa (14~145psi), proof pressure is 1.5MPa (215psi), operating temperature is -20~80℃, and operating speed is 30~800mm/s. The cylinders feature adjustable cushioning and a stroke tolerance range of 0~250. Standard strokes include 24, 32, 37.5, 40, 50, 63, 80, 100, 125 and 150mm. Mounting options include the basic type and accessories such as FA, FB, CA, CB, CR, LB, TC, TCM1 and TCM2. These cylinders are suitable for linear pushing and pulling, clamping and positioning in automated equipment.

FTC Series Standard Cylinders

FTC Series Standard Cylinders

The FTC series comprises standard cylinders powered by compressed air filtered through a 40μm filter. Bore sizes are 32, 40, 50, 63, 80, 100 and 125 mm. The operating pressure range is 0.1~1.0 MPa (14~145 psi), the pressure holding rating is 1.5 MPa, the operating temperature is -20~80°C, and the operating speed range is 30~800 mm/s. The cylinders feature adjustable cushioning. Multiple standard strokes from 24~150 mm are available, along with basic and FA, FB, CA, CB, CR, LB, TC, TCM1 and TCM2 mounting styles, corresponding to the mounting configurations of the MBB, MBBD and MBBJ series. They are suitable for pneumatic actuation in automated fixtures, conveying, positioning and similar applications.

QGA/QGB Series Standard Cylinders

QGA/QGB Series Standard Cylinders

The QGA/QGB series comprises standard double-acting cylinders with bores from Φ32 to Φ400. QGA models have no cushioning, while QGB models have adjustable cushioning. Models from Φ32 to Φ100 use high-quality aluminum alloy cylinder tubes with hard roll-burnished inner surfaces (approximately 30μm thick, hardness MHV400); models from Φ125 to Φ400 use high-precision, ground steel cylinder tubes. The piston rod surface is hard roll-burnished to a hardness of HV1000. The working medium is compressed air filtered through a 40μm or higher-grade filter. Operating pressure is 0.15~1.0MPa, proof pressure is 1.5MPa, and operating temperature is 0~70℃. Standard strokes range from 25~2000mm, maximum strokes range from 500~2000mm depending on bore size, and cushion strokes range from 12~60mm. Mounting styles include basic, FA, FB, CA, CB, CR, LB, TC, FTC, TCM1, and TCM2.

SE Series Standard Cylinders

SE Series Standard Cylinders

SE series standard cylinders are available in seven bore sizes: 32, 40, 50, 63, 80, 100 and 125mm. Three mounting configurations are available: SE (basic type), SED and SEJ. The overall and mounting dimensions of each model match those of the SE standard type. The cylinder barrel, front cover and piston are made of aluminum alloy; the piston rod is made of S45C carbon-manganese-chromium-silicon steel; and the nuts, socket-head bolts and self-tapping screws are made of carbon steel or stainless steel. The front cover O-ring, piston O-ring, wear-ring seals and similar components are made of TPU; O-rings are made of NBR; and the wear rings and bushings are made of wear-resistant materials. The catalog provides the A, AB, AC, AD, AE, B, D, DA, E, F, FA, H, K, M, N, P, PA and PB dimensions for each bore size, as well as the thread specifications at E (M10×1.25~M27×2) and port threads at P (PT1/8~PT1/2). A magnetic version is also available; the non-magnetic version with a carbon steel frame has the same dimensions. Suitable for linear lifting, clamping and positioning in general industrial automation.

DNC Series Cylinders

DNC Series Cylinders

SNS DNC series standard cylinders are double-acting and use air filtered through an approximately 40μm filter. Bore sizes are 32, 40, 50, 63, 80, 100, and 125 mm. Various mounting accessories are available: the basic DNC model supports FA, FB, CA, CB, CR, LB, TC, FTC, TCM1, and TCM2; the DNCJ series is available in a basic version and with FA, LB, TC, ETC, TCM1, and TCM2 options. The catalog provides mounting dimensions such as A, AA, B, C, CA, E, F, and G for accessories including TC, FTC, TCM1, and TCM2 at each bore size. Users can select a mounting method based on bore size and allow sufficient installation space. Accessory mounting positions cannot be adjusted freely.

DNCJ Series Standard Cylinders

DNCJ Series Standard Cylinders

The DNCJ series comprises double-acting standard cylinders available in seven bore sizes: 32, 40, 50, 63, 80, 100, and 125 mm. The operating medium is compressed air filtered through an approximately 40μm filter. The cylinder body is made from an aluminum alloy profile, and a range of mounting accessories is available to suit different applications. DNCJ mounting options include basic, FA, LB, TC, ETC, TCM1, and TCM2; the related DNC series also offers FB, CA, CB, CR, and FTC options. The catalog lists overall and mounting dimensions such as A, AA, B, C, CA, E, F, and G for each mounting accessory by bore size, simplifying selection and equipment layout. Note that accessory mounting positions cannot be adjusted arbitrarily. When selecting a cylinder, check the mounting hole locations and required clearance against the dimension table for the relevant bore size and mounting type.

MGC/MGCD Series Cylinders

MGC/MGCD Series Cylinders

The MGC/MGCD series consists of standard cylinders with bore sizes of 20, 25, 32, 40, 50 and 63 mm, available in single-acting and double-acting versions. The operating medium is compressed air filtered through a 40μm or larger filter mesh. Operating pressure is 0.15~1.0MPa, guaranteed proof pressure is 1.5MPa, and operating temperature is -20~70℃. Standard stroke ranges are ≤200mm for bore size 20 and ≤300mm for bore sizes 25~63; long-stroke ranges are 201~500mm and 301~500mm, respectively. Major components are made from carbon steel, NBR, TPU, aluminum alloy and S45C hard alloy. The design includes impact-absorbing pads and magnets, making these cylinders suitable for linear push-pull, clamping and positioning applications in automated equipment.

ISO 6432 Standard Cylinder

ISO 6432 Standard Cylinder

A standardized cylinder compliant with European standards ISO 6432 and CETOP RP52P, designed for linear pneumatic actuation in automated equipment. The catalog lists six bore sizes: 20, 25, 32, 40, 50 and 63 mm. Short and long strokes are specified separately: for the 20 bore, short strokes are ≤200 mm and long strokes are 201-500 mm; for 25, 32, 40, 50 and 63 bores, short strokes are ≤300 mm and long strokes are 301-500 mm. The page also lists mounting and overall dimensions, including C, CD, CZ, L, RR, TT, TV, TZ and Z, to help select a cylinder by bore and stroke and verify the mounting configuration. For long strokes, some dimensions are shown in parentheses.

MB Series Changtuo Square-Head Cylinder

MB Series Changtuo Square-Head Cylinder

The MB Series Changtuo square-head cylinder features a square-head body and is suitable for pushing, pressing, clamping, positioning, and reciprocating linear motion in automated equipment. According to the catalog, bore sizes of 16-25mm come standard with a magnet but without air cushioning, while bore sizes of 32-40mm come standard with both air cushioning and a magnet. When selecting a model, consider the bore size, stroke, sensor type and quantity, and whether a magnet and air cushioning are required. This series is compatible with the mounting methods used for common standard square-head cylinders.

SC Series Standard Cylinder

SC Series Standard Cylinder

The SC Series Standard Cylinder is a tie-rod, double-acting cylinder featuring a compact design and easy installation. Bore sizes range from 32 to 250 mm, with strokes selectable to suit your requirements. It supports adjustable cushioning or air cushioning and can be fitted with a magnet for position detection. A variety of mounting styles are available, including FA and FB. Suitable for push-pull, clamping, positioning, and other applications in automation equipment. The working medium is compressed air, and the maximum operating pressure is 1.0 MPa.

HCA2 Series Pneumatic Cylinders

HCA2 Series Pneumatic Cylinders

HCA2 series cylinders are standard pneumatic cylinders commonly used in factory automation for linear reciprocating push-pull motion, clamping, positioning and other applications. Bore sizes are 32, 40, 50, 63, 80, 100 and 125 mm. Mounting styles include basic, rear-cover-mounted single clevis, rear-cover-mounted double clevis, front-cover-mounted rod-side flange, rear-cover-mounted rodless-side flange, axial foot and center trunnion. Options include a built-in magnetic ring, double rod and magnetic switches (such as M9B), with a configuration of 2 switches available. Stroke is specified according to the model.

HCDQ2B Standard Type (Through-Hole)

HCDQ2B Standard Type (Through-Hole)

HCDQ2B standard through-hole cylinder, with a bore diameter of 12–25 mm and a stroke of 5–30 mm. Features an externally threaded rod end and hexagonal flats, and is suitable for pneumatic actuation in automated equipment. Its through-hole design has no magnetic ring and supports various mounting options, such as threaded holes at both ends and a protruding plug on the rodless side. Made from materials that meet industry standards, it offers high dimensional accuracy and reliability. Widely used in mechanical manufacturing and automated production lines.

HCP95 Series Square-Body Cylinders

HCP95 Series Square-Body Cylinders

The HCP95 series is a range of standard square-body cylinders with mounting surfaces on all four sides for flexible attachment in multiple directions. Seven bore sizes are available: 32, 40, 50, 63, 80, 100 and 125 mm. The stroke can be selected as needed (the catalog example has a 32 mm bore and a 200 mm stroke). Mounting options include basic (B), axial foot (L), rod-end flange (F), head-end flange (G), single clevis (C), double clevis (D) and center trunnion (T), accommodating horizontal, vertical, suspended and pivoting installations. Piston rod options include a standard single rod (blank) or double rod (W), for anti-rotation or synchronized movement at both ends. The cylinder can be fitted with magnetic switches; the catalog example uses switch code Z73, with 2 switches in the standard configuration. The complete model number is assembled in the sequence HCP95-fixing type-type code-mounting type-bore-stroke-magnetic switch, for example HCP95SDB32-200-Z73.

HCP96 Series Square-Body Cylinders

HCP96 Series Square-Body Cylinders

The HCP96 series features a square cylinder body and is suitable for linear push-pull, clamping, and positioning applications in industrial automation equipment. Bore sizes include 32, 40, 50, 63, 80, 100, and 125 mm. Mounting options include basic, axial foot, rod-side flange, non-rod-side flange, fixed rear cover (double-clevis type), single eye, double clevis, and center trunnion, accommodating different mounting orientations and load requirements. Standard single-rod and W double-rod versions are available, and 2 magnetic switches can be fitted for position detection. Specify the bore size, stroke, mounting type, and piston rod configuration when selecting a model.

HCQ2A Series Standard Cylinder

HCQ2A Series Standard Cylinder

The HCQ2A series features cylinders with threaded holes at both ends, bore sizes from 12 to 100 mm, and strokes from 5 to 50 mm. Multiple mounting options are available, including a raised cap on the rodless side and external threads on the rod end. Suitable for automation equipment, workholding fixtures, and other applications.

HDCQ2A Series Standard Cylinder

HDCQ2A Series Standard Cylinder

The HDCQ2A series features cylinders with threaded holes at both ends and bore sizes ranging from 32 to 100 mm. Multiple mounting options are available, including an extended cover on the rodless side and an external thread on the rod end. The cylinder body is made of carbon steel for mechanical castings, with a specially finished inner wall for a smooth surface and long service life. Suitable for automation equipment, special-purpose machines, jigs, and fixtures, these cylinders can be paired with a flow control valve to adjust speed.