product — Page 53

FAG Series Electric Slides

FAG Series Electric Slides

The FAG series is a standard electric slide range from FARAY AUTOMATION. This page defines the electrical specifications for the series. The slide uses a 15-pin male connector: Pins 1–4 are the A/A/B/B two-phase motor winding leads, Pin 6 is the CWLS (clockwise limit) output, Pin 7 is the CCWLS (counterclockwise limit) output, Pin 9 is the DC+24V power input, Pin 10 is the ORG1 slide travel origin output, Pin 11 is DC 0V, and Pin 12 is ground. Pins 5, 8, and 13–15 are unused. The timing diagram shows the operating relationships among the slide travel slot block, CW/CCW limits, origin sensor, hardware limits, and motor, and is used to wire the host controller for homing and limit protection. When selecting and wiring the slide, check the pin assignments against the wiring diagram to avoid reversing the power and signal connections. All travel lengths in the series share the same electrical specifications.

PRP Series Two-Phase Stepper Motors

PRP Series Two-Phase Stepper Motors

The PRP series comprises two-phase stepper motors with dual output shafts, primarily used to drive factory automation equipment such as linear modules, slides and positioning stages. The series is divided into A/B/C/D groups by motor mounting configuration, each corresponding to different flange sizes and output torque ratings. This makes it easy to match a motor to the load and available installation space when selecting a module. For example, the PRP223D15B2 and PRP225D15B2 both have a 1.8° step angle, a rated current of 1.5A and a flange size of □28mm. Their body lengths are 32mm and 51.5mm, maximum holding torques are 0.095 N·m and 0.19 N·m, and rotor inertias are 0.09×10⁻⁴ and 0.18×10⁻⁴ kg·m², respectively. The GTR22G-D driver is available separately for use with these motors. The same catalog table also lists interchangeable motor options, including the Taiwanese 2MS series, Japanese SH/PKP series, and motors from Oriental Motor and Sanyo Denki, to suit different cost and precision requirements.

PKP Series Two-Phase Stepper Motors

PKP Series Two-Phase Stepper Motors

PKP series two-phase stepper motors feature a Japanese-style dual-shaft design and a 1.8° step angle. Available in □35mm and □42mm frame sizes, they have a rated current of 2.3A and maximum holding torques of 0.2N·m and 0.58N·m, respectively. The compatible driver model is GTR22G-D. Designed for precision positioning and motion control in factory automation equipment, they can be used with a variety of linear modules and slides.

CVRD Series Stepper Motors

CVRD Series Stepper Motors

The CVRD series is a matched system of stepper motors and drivers organized by motor mounting group. The catalog compares compatible stepper motor specifications across four groups: A, B, C, and D. Each group corresponds to a mounting flange size and rated current, covering Taiwanese two-phase stepper motors, Japanese two-phase and five-phase dual-shaft stepper motors, and motors from brands such as Oriental Motor and SANYO. The table lists rated current (0.67A~2.3A), dimensions (□28×31.3 to □42×47, among others), step angle (1.8°, 0.72°, 0.36°), maximum holding torque (0.06~0.58 N·m), rotor inertia, and recommended driver models (such as CVRD215-K, CVRD223-K, CVRD518-K, and GTR22G-D). Users can select a motor and its corresponding group based on mounting dimensions and torque requirements, then choose a CVRD series driver from the same group for a matched motor-and-driver combination.

FR/FX Series Stepper Motors

FR/FX Series Stepper Motors

FR/FX series stepper motors are used for positioning, conveying, and power transmission in factory automation equipment. The catalog organizes motor selection into A/B/C/D groups by mounting classification and lists specifications by motor type/shaft configuration, rated current, external dimensions, step angle, maximum holding torque, rotor inertia, and optional driver models. Models shown include FR, FXN, and FXG types (such as FR39-LND, FXN50100-SBN, and FXG6-35CS), with optional drivers including GTR22G-D, GTR24M3, and CVRD518-K. Refer to the corresponding model table for each model's current, dimensions, step angle, torque, and rotor inertia; OCR misalignment in the table on this page prevents these values from being reliably matched to individual models.

SH Series Two-Phase Stepper Motors

SH Series Two-Phase Stepper Motors

SH series two-phase stepper motors have dual output shafts and are compatible with motor mounting groups A/B/C/D. Common frame sizes include □28, □35, and □42 mm, with rated currents of approximately 0.75~1.5 A and step angles of 0.36°, 0.72°, and 1.8°. Maximum energized holding torque is approximately 0.041~0.37 N·m, and rotor inertia is approximately 1×10⁻⁶~7.4×10⁻⁶ kg·m². Optional drivers include the GTR24M3 and CVRD518-K. These motors are suitable for positioning, feeding, and drive applications in automated equipment.

SANYO 103 Series Stepper Motors

SANYO 103 Series Stepper Motors

The SANYO 103 series is a family of compact stepper motors for positioning and motion control in factory automation. They are commonly used in linear modules, slides, dispensing machines, and inspection equipment. The catalog groups motors into A/B/C/D mounting categories, lists their compatibility with module-side motor mounts, and provides specifications such as rated current, flange size, step angle, holding torque, and rotor inertia. Models shown include 103H5210-0410, 103-4507-7010, and 103F5510-8211, with flange sizes of approximately 39~42 mm, rated currents of 1.2~1.4 A, step angles of 0.72°/1.8°, holding torques of 0.078~0.37 N·m, and rotor inertias of approximately 0.022×10⁻⁴~0.074×10⁻⁴ kg·m². They can be paired with drivers such as CVRD518-K and GTR24M3. The table also lists Taiwanese, Japanese, and Oriental motor equivalents for comparison; these are not primary models in this series.

Medium-Duty Quiet Casters

Medium-Duty Quiet Casters

This series includes two designs: medium-duty quiet TPR wheels and medium-duty quiet all-plastic wheels. Suitable for clean, smooth indoor floors, they offer quiet operation, wear resistance, easy rolling, responsive swivel action, and excellent elasticity. They are commonly used on medical equipment and in healthcare environments. The TPR wheels feature rust-resistant, chrome-plated inner brackets designed to prevent fiber buildup, and precision ball bearings. The environmentally friendly all-plastic wheels are also suitable for medical applications. Load capacity: 60–100 kg; overall height: 108–178 mm; wheel diameter: 3–5 inches; center-hole sizes: 56 × 40 mm or 75 × 45 mm. Operating temperature: −35 to 80°C. For low-speed transport, keep speed below 2 km/h.

JQC Series Compact Cylinders

JQC Series Compact Cylinders

The JQC series consists of compact cylinders with a short axial length and a flat profile, making them suitable for installations where space is limited. They provide short-stroke linear motion for clamping, positioning, ejecting and stopping workpieces. The catalog specifies ordering codes in the format “series number + bore + stroke + magnetic switch.” For example, JQC-12×30-M9BW denotes a 12 mm bore, a 30 mm stroke and an M9BW magnetic switch. Bore and stroke are selected from standard sizes. The cylinder body typically has mounting grooves for magnetic switches, which can be added for position detection and signal feedback. Common mounting options include through-holes (standard type) and threaded holes at both ends, and the cylinders can be used with various brackets, clevises and flanges. The working medium is filtered compressed air. Oil-mist lubrication is required unless a non-lube version is selected. Refer to the product label and official technical documentation for operating pressure, proof pressure, operating speed and operating temperature range.

MGG Series Compact Guided Cylinder

MGG Series Compact Guided Cylinder

The MGG series compact guided cylinder integrates a cylinder and guide mechanism into a compact pneumatic actuator. Two parallel guide rods work with a guide plate to provide resistance to twisting and offset loads while delivering linear thrust. Grippers, suction cups, press heads, and other end effectors can be mounted directly for precision guiding, positioning, press-fitting, and pick operations in automated equipment. Compared with a standard cylinder, it is shorter, more compact, and more rigid, can withstand a certain amount of lateral load, and offers consistent repeat positioning accuracy. The catalog gives MGG B 32×100 R as an example model code: MGG series, B construction type, 32mm bore, 100mm stroke, and R option. When selecting a model, users primarily specify the bore, which determines output thrust, and the stroke, which determines the operating range, then add suffixes for mounting and accessories such as magnetic switches. This series often appears in the same catalog as TDA and CXS dual-rod cylinders and STM slide table cylinders, offering an additional compact guided cylinder option.

TDA Series Twin-Rod Cylinder

TDA Series Twin-Rod Cylinder

The TDA series is a twin-rod cylinder with two parallel piston rods, offering rotation resistance, precise guidance, and strong load capacity. It is suitable for automated equipment requiring anti-rotation and precise guidance. This standard series can be used with a wide range of automated equipment. Refer to the catalog for detailed specifications, including bore sizes, strokes, and mounting options.

CXS Series Twin-Rod Cylinder

CXS Series Twin-Rod Cylinder

The CXS series is a twin-rod guided pneumatic cylinder. Two parallel piston rods drive a shared end plate, enabling it to withstand moderate radial and eccentric loads while effectively preventing rod rotation. It is suitable for applications requiring anti-rotation, higher positioning accuracy, or simultaneous pushing and clamping of workpieces. The series is widely used in automation equipment, fixtures, conveyor lines, and assembly lines. Selection is based primarily on bore size, stroke, mounting configuration (such as basic or magnetic switch-equipped), and whether an internal magnetic ring is provided for magnetic switch installation. This catalog page lists only the series and product names; specific bore and stroke sizes must be confirmed using the complete model code. The cylinder typically uses clean, dry compressed air as its working medium. During installation, ensure both rods are loaded evenly to prevent uneven loading on one side from causing abnormal seal wear.

STM Series Slide Table Cylinder

STM Series Slide Table Cylinder

The STM series slide table cylinder is a guided linear pneumatic actuator consisting of a cylinder body, two guide rods, and a sliding platform. The piston rod drives the platform in precise reciprocating motion along the guide rods. Workpieces, fixtures, or sensors can be mounted directly on the platform, which offers better resistance to torsion and off-center loads than a conventional single-rod cylinder. Common selection parameters include bore size (compact sizes such as 6, 10, 16, 20, 25, and 32), stroke (short strokes from a few millimeters up to around 100 mm), operation (single-acting spring return or double-acting), magnetic switches (available with a magnetic ring), and mounting style (basic, flange, etc.). This series is often considered alongside compact guided cylinders such as MGG and dual-rod cylinders such as TDA/CXS. It is widely used in automated electronic assembly, packaging, inspection, and fixture positioning equipment where compact size, short stroke, and smooth guided motion are required. This catalog page provides only the series name and product image; specific bore, stroke, magnet, and other specifications must be confirmed using the selection chart.

CXSW Series Twin-Rod Cylinder

CXSW Series Twin-Rod Cylinder

The CXSW series is a twin-rod cylinder with two parallel piston rods that operate simultaneously. It offers strong resistance to torsion and off-center loads, as well as high guiding accuracy. It is suitable for clamping, lifting, transfer and other applications where workpiece rotation must be prevented or lateral loads must be supported. Bore sizes are 32, 40, 50, 63, 80 and 100 mm, with standard strokes from 10 mm to 100 mm (10/20/30/40/50/75/100). An integrated magnetic ring is optional (S indicates a magnet; a blank position indicates no magnet), allowing position detection with a magnetic switch. Mounting options include basic, rear single clevis CA, rear double clevis CB, front flange FA, rear flange FB, foot mount LB, trunnion mount TC, and trunnion mount with foot bracket TC-M. The ordering code combines the series code, bore, stroke, magnet code and mounting type in sequence, for example CXSW-M-20x50-□-Y59A.

SC Series Standard Cylinder

SC Series Standard Cylinder

The SC series standard cylinder (concealed tie-rod type) features an aluminum alloy barrel and concealed tie rods for linear reciprocating motion in automated equipment. Bore sizes include 32, 40, 50, 63, 80, and 100 mm, with stroke lengths from 10~100 mm available. The model code specifies, in order, the series number, bore, stroke, adjustable stroke (N adjustable stroke distance / S with magnet), magnet code (S with magnet, blank without magnet), and mounting type (basic type, CA rear single clevis, CB rear double clevis, FA front flange, FB rear flange, LB foot mounting, TC pivot mounting, TC-M pivot mounting with foot bracket). Multiple variants are available, including standard double-acting, double-rod, adjustable double-rod, and multi-position types, with flexible mounting options.

SI Series Standard Cylinders

SI Series Standard Cylinders

SI series standard cylinders feature concealed tie rods and are available in standard, double-rod, adjustable double-rod, and multi-position configurations. Bore sizes range from 32~100mm, and the stroke can be selected to suit the application. Options include an adjustable stroke (N), a built-in magnet (S), and various mounting styles, such as FA front flange, CA single clevis, CB double clevis, LB foot mount, and TC trunnion mount. Compact and easy to install, these cylinders provide pneumatic actuation for a wide range of automated equipment.

DNC/SE Series Standard Cylinders

DNC/SE Series Standard Cylinders

DNC/SE series standard cylinders are general-purpose, double-acting cylinders with mounting dimensions compliant with the ISO6431 international standard. Bore sizes include 32, 40, 50, 63, 80, 100 and 125 mm, with common stroke lengths of 10, 20, 30, 40, 50, 75, 100 and 125 mm to meet most linear push-pull requirements. The cylinders feature an aluminum alloy barrel and concealed tie rods for a compact design. Standard mounting holes allow interchangeable installation with a wide range of international standard cylinders. An optional built-in magnetic ring (MDB type) enables position detection with magnetic switches. Mounting accessories include SNCB double-clevis mounts, single-clevis mounts and HNC foot mounts, supporting flange, foot, clevis and pivoting configurations. Pneumatic cushioning (PPV) reduces impact and noise at the end of the stroke, while the adjustable stroke (N) option provides mechanical travel limiting for certain applications. These cylinders are widely used in automated assembly lines, packaging machinery, tooling and fixtures, and material handling.

CPT All-Plastic Twin Wheel

CPT All-Plastic Twin Wheel

CPT all-plastic twin wheels are designed for use on hard floors in environments that are kept clean. They feature a simple, attractive design that is easy to clean. The brackets are injection-molded from a specially formulated PA nylon, making them lightweight, highly load-bearing, and highly impact-resistant. Precision ball bearings allow the wheels to turn smoothly and with less effort. The standard configuration has white brackets and thread guards with gray PU treads. Mounting options include a swivel plate and a brake. Available in 3-, 4-, and 5-inch sizes, with load capacities of 30–80 kg, heights of 98–155 mm, PC-TPR material, and center hole sizes from 50 × 40 to 75 × 45 mm.

MBB Series Standard Cylinders

MBB Series Standard Cylinders

MBB series standard cylinders are tie-rod cylinders suitable for linear pushing and pulling, clamping, lifting, and other industrial automation applications. The catalog includes the basic MBB model and the MDBB model with a built-in magnetic ring. Common bore sizes are 32, 40, 50, 63, 80, 100, and 125 mm, with stroke options including 10, 20, 30, 40, 50, 75, 100, 125, and 150 mm. Adjustable stroke, a built-in magnet, and mounting styles such as FA/FB/CA/CB/LB/TC/TC-M can be selected as needed. An example model code is MBB 50×150-N S FA.

MAL Series Aluminum Alloy Mini Cylinders

MAL Series Aluminum Alloy Mini Cylinders

MAL series mini cylinders feature an aluminum alloy body and a compact, lightweight design. They are suitable for pushing, pulling, clamping, and positioning applications where space is limited in automated equipment. The series includes basic, dual-rod, and adjustable dual-rod versions, with bore sizes of 16, 20, 25, 32, and 40 mm and common stroke lengths of 10, 20, 25, 32, 40, and 50 mm. Options include a magnet (S) and mounting styles such as a front flange (FA). The model code typically consists of the MAL series designation, bore × stroke, magnet code, and mounting style. These cylinders can be used with pneumatic control valves, fittings, and magnetic switches.

MA Series Stainless Steel Mini Cylinder

MA Series Stainless Steel Mini Cylinder

The MA series is a compact, double-acting stainless steel mini cylinder for pneumatic applications. Its corrosion-resistant stainless steel barrel and compact design make it suitable for light-duty automation tasks in confined spaces, including clamping, sorting, positioning and pushing. The ordering code combines the series number, bore, stroke, magnet code and mounting type in sequence. The magnet code indicates whether a magnetic ring is built in for position detection by an externally mounted magnetic switch; the mounting type specifies accessories such as FA. Common bore sizes include 32 and 50, and the stroke is selected from the standard range according to operating conditions. Mounting options include the basic type or versions with accessories such as flanges or clevises. Write the complete ordering code in the order “series number-bore-stroke-magnet code-mounting type,” and check that the stroke is compatible with the bore and that the mounting accessory threads are correct.

CJP Series Pin Cylinder

CJP Series Pin Cylinder

The CJP series pin cylinder, also known as a pen cylinder, is a compact, lightweight, single-acting miniature cylinder with spring return. It is suitable for precision positioning, workpiece ejection, stopping, sorting, and driving small fixtures in industries such as electronics, semiconductors, medical devices, and packaging. Bore sizes are 6, 10, and 15 mm, with primarily short strokes such as 5 mm. The mounting type is B (basic type), with direct threaded or flange mounting. Optional magnetic switches, such as 1973K, 1195K, and 1197K, provide position detection. The cylinder body is typically made of stainless steel or aluminum alloy, offering corrosion resistance, fast response, and a long service life. To select a model, combine the specifications in the order “bore diameter-stroke-mounting type.” For example, a CJPB cylinder with a bore of 10, a stroke of 5, and mounting type B is designated CJPB10×5-B.

CJP Series Double-Acting Pin Cylinders

CJP Series Double-Acting Pin Cylinders

The CJP series double-acting pin cylinder (CJPB type) is a compact, lightweight pneumatic actuator with a slender, pin-shaped piston rod. It is primarily used for lifting, positioning, pushing, and clamping in confined spaces in electronics, semiconductors, precision assembly, and inspection fixtures. Six bore sizes are available: 6, 10, 15, 20, 25, and 32 mm. Six stroke lengths are available: 10, 15, 20, 25, 32, and 40 mm. Model numbers follow the sequence “series number-bore-stroke-double-acting-rod end thread”: D denotes the double-acting type; the rod end can be threaded (blank) or unthreaded (B). The basic type does not include a switch mounting rail. Flange-mounted and magnet-free variants are also available, and some models can be fitted with magnetic switches for position detection. These cylinders are suited to high-frequency, short-stroke precision applications.

MXQ Series Pneumatic Slide Table

MXQ Series Pneumatic Slide Table

The MXQ series pneumatic slide table (recirculating linear guide/twin-cylinder type) is a pneumatic actuator designed for precise linear motion in automated equipment. Its recirculating linear guide and twin-cylinder drive provide high rigidity and guiding accuracy, allowing it to withstand moderate eccentric loads and moments while delivering smooth motion and repeatable positioning. The series is suitable for linear conveying, positioning, press-fitting, and transferring workpieces, and is commonly used with pneumatic components such as cylinder control valves and magnetic switches. When selecting a model, consider the bore size, stroke, mounting method, and load conditions to ensure that the slide operates within its permissible load range.

CUJ Series Miniature Free-Mount Cylinders

CUJ Series Miniature Free-Mount Cylinders

The CUJ series miniature free-mount cylinders, also referred to as the CU series in the original title, include the CUJB basic type and versions with a built-in magnetic ring. Their compact size and flexible mounting orientations and methods make them suitable for short-stroke pushing, clamping, and positioning in space-constrained applications such as electronics assembly, packaging, and fixtures. The model codes in the catalog begin with CUJB, with bore options including Φ4, Φ6, Φ10, Φ20, and Φ32. Some table rows contain OCR duplications or expansions; refer to the original catalog for authoritative specifications. CS1-U, CS1-F, CS1-S, CS1-G, D-A73, D-Z73, D-C73, and D-A93 magnetic switches can be fitted for position detection.

Heavy-Duty PU Casters

Heavy-Duty PU Casters

Heavy-duty PU casters are made of polyurethane (PU) and offer excellent wear, oil, and chemical resistance, along with high strength and shock absorption. This series is available in a range of specifications, with load capacities of 180–260 kg, mounting heights of 100–200 mm, wheel diameters of 4–8 inches, and a mounting-hole spacing of 84 × 71 mm. Three bracket types are available: braked, fixed, and swivel. They are suitable for heavy machinery, hand trucks, tool carts, and other applications. The PU elastomer wheels are quiet, highly load-bearing, and tear-resistant, making them suitable for long-term use in demanding environments.

FV Series Foot Valves

FV Series Foot Valves

The FV series comprises pneumatic foot-operated directional control valves. Pressing the pedal changes the spool position to control the extension and retraction of cylinders and other actuators. These valves are suitable for applications where both hands are needed for the work and cannot be used to operate a valve. Common applications include tube benders, welding equipment, press-fitting equipment, packaging machinery, and various tooling and fixtures. The series includes two basic valve types: 320 (3-port, 2-position) and 420 (5-port, 2-position). The third position uses 2 to indicate the 200 series size. The valve body has a plate-mounted/direct-acting design. Port size and operating pressure are determined by the selected 200 series specification, and the panel should be selected according to the actual pipe size and air supply pressure. During installation, allow sufficient space for pedal travel and consider the exhaust direction. Protect the pedal pivot from direct exposure to dust and cutting fluid.

Heavy-Duty Fenghuo Casters

Heavy-Duty Fenghuo Casters

The Heavy-Duty Fenghuo caster series features a polyolefin wheel core wrapped in highly wear-resistant polyurethane, offering excellent wear resistance, noise reduction, and floor protection. The brackets are made from premium steel plate with a galvanized finish and feature anti-wrap guards, making them suitable for uneven surfaces. Available in three mounting types—braked, fixed, and swivel—with load capacities of 180–260 kg and heights of 100–200 mm, these casters fit 4–8 inch wheels. The mounting-hole spacing is 84 × 71 mm. Suitable for industrial applications such as logistics facilities and heavy machinery.

JMJ Series 5-Port 2-Position Mechanical Valves

JMJ Series 5-Port 2-Position Mechanical Valves

The JMJ series 5-port 2-position mechanical valve is a mechanically operated pneumatic control component used to control the direction of cylinders and other actuators in automated equipment. The series features a robust valve body and a G1/4" port size, with position code 52 indicating a 2-position 5-way configuration. Actuator options include basic, roller, selector knob, locking button, flat button, projecting button and large round button styles to meet different operating needs. The model code follows the format JMJ[position]-[port size][button]. For example, JMJ52-2R denotes a 5-port 2-position mechanical valve with G1/4" ports and a roller actuator. These valves are widely used on automated production lines in the packaging, food, textile and electronics industries.

MAR Series Precision Pressure Regulator

MAR Series Precision Pressure Regulator

The MAR series precision pressure regulator provides precise pressure reduction and regulation of compressed air in pneumatic systems. The standard pressure adjustment range is 0.05~0.85MPa. Four low-pressure versions, 1K, 2K, 3K and 4K, offer ranges of 0.05~0.1MPa, 0.05~0.2MPa, 0.05~0.3MPa and 0.05~0.4MPa, respectively. The specification code includes sections for the model, port/thread and options. Confirm specific combinations against the complete coding rules. It is suitable for pneumatic control circuits requiring highly stable output pressure.

AC Series Hydraulic Shock Absorbers

AC Series Hydraulic Shock Absorbers

AC series self-compensating hydraulic shock absorbers absorb impact energy in automation equipment, conveyor lines, cylinder end-of-stroke applications, and other mechanisms, reducing noise and vibration. They feature an externally threaded body. The model number consists of the series code AC, external body thread size, impact stroke, impact speed, and shock absorber cap option. Impact speeds are available in three grades: high, medium, and low. Cap options are with cap (blank) or without cap (N). Select the appropriate model based on load, impact speed, and stroke to ensure effective cushioning and service life.

SCI Series Ball Screws

SCI Series Ball Screws

The COMTOP SCI series ball screw catalog lists 15 standard models with nominal diameters d=16~80 mm, leads of 4~10 mm, ball diameters of 2.381~6.35 mm, nut outer diameters of 30~105 mm, and nut lengths of 40~85 mm. The table also lists dimensions and load parameters including L1, L2, M, R, n, Ca, Coa, and K; n is 4 for all models. Models marked ★ can be made with left-hand threads. These ball screws are suitable for automated drive applications that convert rotary motion into linear motion. Select a model based on diameter, lead, mounting dimensions, and dynamic and static loads.

SFS Series High-Speed, Low-Noise Ball Screws

SFS Series High-Speed, Low-Noise Ball Screws

The SFS series consists of high-speed, low-noise ball screws with screw and nut configurations conforming to DIN 69051 FORM B. They are suitable for applications requiring high rotational speeds, low noise, and low vibration, such as CNC machine feed axes, automated assembly lines, semiconductor and electronics equipment, and precision measurement platforms. The nut incorporates an oil hole for connection to a centralized lubrication system or grease supply line, helping maintain a lubricating film and reduce temperature rise and noise during high-speed reciprocating motion. The catalog presents dimensions in a dimension table. Selection is typically based on nominal outside diameter, lead, nut type, overall screw length, thread length, and accuracy grade. Engineering selection also requires verification of the DN value, critical speed, permissible axial load, and buckling stability. The catalog content on this page primarily provides the table structure and model designation (SFS / DIN 69051 FORM B); refer to the complete catalog pages or manufacturer drawings for specific dimensions and individual models.

DFS Series High-Speed, Low-Noise Ball Screws

DFS Series High-Speed, Low-Noise Ball Screws

The COMTOP DFS series consists of high-speed, low-noise ball screws with a flanged nut design conforming to DIN 69051 FORM B. An oil hole on the nut end face facilitates centralized oil supply and routine lubrication. Designed for low noise, high rotational speeds and low vibration, the series is suitable for high-speed machine tool feeds, injection molding machines, automation equipment and other applications requiring fast response and quiet operation. The nut flange conforms to DIN 69051 international standard mounting dimensions, allowing interchangeability with various support units and nut housings. As this page is a catalog specification sheet, refer to the relevant specification table for nominal diameter, lead, stroke and accuracy grade. Models are generally selected based on the combination of nominal diameter, lead and accuracy grade.

SFV Series High-Speed, Heavy-Duty Ball Screws

SFV Series High-Speed, Heavy-Duty Ball Screws

The SFV series is COMTOP’s range of high-speed, heavy-duty ball screws. Designed for applications involving both high speeds and substantial axial loads, the series features optimized ball recirculation paths and nut interiors to increase critical speed and DN values while reducing operating noise and heat buildup. It combines high-speed responsiveness with load-bearing rigidity, making it suitable for high-speed reciprocating applications with heavy loads, including CNC machine tool feed axes, injection molding machines, dedicated automation machinery, and handling and positioning systems. Key selection parameters include screw outside diameter, lead, overall screw length, thread length, accuracy grade, nut type (including flanged or cylindrical designs and oil port configuration), and axial clearance or preload grade. The catalog provides dimensional tables listing dynamic and static load ratings and nut mounting dimensions for each diameter and lead combination. The required stroke and shaft-end machining must be determined from the applicable drawings.

DFV Series High-Speed Heavy-Duty Ball Screws

DFV Series High-Speed Heavy-Duty Ball Screws

The COMTOP/TBI DFV series consists of high-speed, heavy-duty ball screws with multi-turn recirculation and optimized groove geometry. They are designed for automated equipment and machine tool feeds requiring high speed, high rigidity, and heavy cutting. Nominal diameters range from 15~80 mm, with leads of 5/10/20 mm, ball diameters of 3.175/6.35/9.525 mm, and 2.7~7.6 ball turns. The model code is DFV+nominal diameter (3 digits)+lead (2 digits)-number of turns (e.g., DFV04010-4.8). The specification table provides reference data including nut flange dimensions, dynamic load rating Ca, static load rating Coa, and rigidity K. Left-hand threads are also available. Applications include CNC machine tools, precision positioning stages, injection molding machines, and various high-speed, heavy-duty drive mechanisms.

Heavy-Duty Korean-Style Anti-Wrap Caster

Heavy-Duty Korean-Style Anti-Wrap Caster

The heavy-duty Korean-style anti-wrap caster features a protective cover that prevents debris from getting caught and interfering with wheel rotation. It is widely used on hand trucks, tool carts, and machinery. The wheel core is made of cast iron, which is tough and ductile, while the tread is made of polyurethane elastomer (PU), offering excellent wear and chemical resistance, high strength and elasticity, resistance to heavy loads and high pressure, tear resistance, radiation resistance, and shock absorption. The semi-arched tread design reduces initial resistance when turning. Available in four sizes: 4, 5, 6, and 8 inches. Load capacity ranges from 350 to 700 kg, mounting height from 100 to 200 mm, and bolt-hole spacing is 84 × 71 mm. Choose from braked, rigid, and swivel types to suit different applications.

SFI Series Ball Screws

SFI Series Ball Screws

The SFI series comprises COMTOP ball screws with nominal diameters of 16, 20, 25, 32, 40, 50, 63, and 80 mm; leads of 4, 5, and 10 mm (including a 5.08 mm option); ball diameters of 2.381~6.35 mm; and 3 or 4 circuits. They are suitable for automation equipment, precision positioning, and linear motion. The table lists dynamic load ratings of 640~5620 kgf, static load ratings of 1249~21300 kgf, and stiffness of 15~90 kgf/μm. Models marked ★ can be manufactured with left-hand threads.

DFI Series Ball Screws

DFI Series Ball Screws

The DFI series consists of flanged, internally recirculating ball screws with 4 ball circuit turns inside the nut. Nominal diameters are 16, 20, 25, 32, 40, 50, 63, and 80 mm, with leads of 4/5/10 mm and ball diameters of 2.381~6.35 mm. The nut has a flange and an M6/M8 oil hole for easy lubrication and maintenance. Dynamic load ratings range from 640~5620 kgf, static load ratings from 1340~21300 kgf, and stiffness from 35~162 kgf/μm. These ball screws are suitable for automation equipment, machine tool feeds, precision positioning mechanisms, and other applications requiring high-rigidity, low-backlash linear motion. Models marked ★ can be manufactured with left-hand threads.

SFU Series Ball Screws

SFU Series Ball Screws

COMTOP SFU series ball screws are rolled, flanged ball screws conforming to DIN 69051 FORM B, suitable for general motion and positioning applications. Specifications cover nominal diameters d12~d100 mm, leads of 4~20 mm, ball diameters of 2.381~9.525 mm, nut outside diameters D24~150 mm, flange diameters A40~202 mm, flange thicknesses B10~30 mm, overall nut lengths L40~180 mm, flange mounting hole diameters X4.5~17.5 mm, flange heights H30~155 mm, M6 or M8 oil hole threads, and 3 or 4 ball circuits n. Basic dynamic load ratings Ca range from 593~9420 kgf, and basic static load ratings Coa range from 1129~39183 kgf. Sizes marked ★ can be manufactured with left-hand threads; rolled-grade sizes such as d32 and d40 are regularly stocked.

DFU Series Ball Screws

DFU Series Ball Screws

The DFU series consists of DIN 69051 FORM B flanged ball screws manufactured by COMTOP. They are available in nominal diameters of 16~100 mm, leads of 4~20 mm, and ball diameters of 2.381~9.525 mm. The catalog provides nut and mounting dimensions D, A, B, L, W, X, H, Q, and n, as well as dynamic load rating Ca and static load rating Coa. These ball screws are suitable for automated drive applications that convert rotary motion into linear motion. Some models are available with left-hand threads, marked with ★ in the original catalog.

SFT Series Ball Screws

SFT Series Ball Screws

The SFT series consists of internal-recirculation ball screw assemblies with a screw shaft and flanged nut, suitable for precision motion applications such as machine tool feeds, automated equipment, and linear modules. The catalog provides complete dimensional and performance data in a reference table: nominal diameters d of 20, 25, 32, 40, 50, 63, and 80 mm; leads I of 5, 6, 8, 10, and 20 mm; and ball diameters Da of 3.175, 3.969, 4.762, 6.350, and 9.525 mm. The number of ball circuits n is available in three configurations: 2.5×1, 2.5×2, and 2.5×3, corresponding to 2.5, 5, and 7.5 total turns. The table also lists nut outside diameter D, flange and overall dimensions L, W, and H, mounting hole positions X, Y, and Z, lubrication port thread Q (M6, M8), dynamic load rating Ca, static load rating Coa, and stiffness K to help select a model based on load and accuracy requirements. Models marked ★ can be made with left-hand threads.

DFT Series Ball Screws

DFT Series Ball Screws

COMTOP DFT series ball screws feature a Q lubrication port on the nut for direct grease injection or connection to a centralized lubrication system, making them suitable for automated equipment operating continuously for extended periods. The catalog provides a reference data table with key parameters for each model: lead Lead, ball diameter Da, number of ball turns n, rigidity K (Kgf/μm), dynamic load rating Ca (Kgf), and static load rating Coa (Kgf). To select a model, first determine the shaft diameter and lead based on the available installation space and required thrust. Then select the ball diameter and number of ball turns by comparing rigidity and dynamic and static load ratings against the load and positioning accuracy requirements. More ball turns increase rigidity and load ratings, but also increase friction and heat generation. These ball screws are suitable for applications requiring high-precision linear positioning, including CNC machine feed axes, XY stages, injection molding machines, semiconductor equipment, and inspection equipment.

SFE Series Ball Screws

SFE Series Ball Screws

The SFE series consists of COMTOP rolled-grade, flanged ball screws with right-hand threads. The flanged ball nut has 4 mounting through-holes and an M6 oil port for easy installation and centralized lubrication. Screw outer diameters are 16, 20, 25, 32, 40, and 50 mm. Standard leads match the screw diameter (16~50 mm), with 10 mm lead versions also available. Ball nuts are available with 2 ball circuits (A2) or 4 ball circuits (A4); the dynamic and static load ratings of the 4-circuit design are approximately 1.8~2.0 times those of the 2-circuit design. The specification table lists dynamic load ratings Ca of 650~7260 kgf, static load ratings Coa of 1280~27600 kgf, and maximum screw lengths of 3000~6000 mm, increasing with screw diameter. The model code is SFE + thread direction + screw outer diameter + lead + number of ball circuits + flange type + rolled grade + accuracy grade (C10). These ball screws are suitable for linear motion and positioning in general industrial automation, conveyor lines, packaging machinery, and woodworking machinery.

SFM Series Ball Screws for Milling Machines

SFM Series Ball Screws for Milling Machines

This series of ball screws is designed for milling machines and is listed in the catalog as the SFM type. The table lists two models, SFM03205-4 and SFM0325T-4, with leads of 5/5.08 mm, a ball diameter of 3.175 mm, 4 ball circuits, a dynamic load rating of 1450 kgf, a static load rating of 4150 kgf, and stiffness of 40 kgf/μm. Ball nut dimensions include D48, A74, B12, L52/53, W60, and H60, along with mounting holes and M8 threads. They are suitable for milling machine feed drives. The same page also lists the DFM type, which is a different type and is not included in this series' SKUs.

DFM Series Ball Screws for Milling Machines

DFM Series Ball Screws for Milling Machines

DFM series ball screws are designed specifically for precision transmission in milling machine tables and feed axes. Their special nut design provides high rigidity and load capacity: ball diameter 3.175mm, 4 ball circuits, dynamic load rating Ca 1450 Kgf, static load rating Coa 4150 Kgf, and rigidity K 72 Kgf/μm. Two models are listed: DFM03205-4 (corresponding shaft diameter/lead 5mm) and DFM0325T-4 (5.08mm). Both have nut dimensions of 74×12mm and M8 mounting holes, with mounting dimension B of 102mm and 104mm, respectively. They can be selected as alternatives to the SFM models on the same page (B 52/53mm, K 40 Kgf/μm). Models marked ★ can be manufactured with a left-hand thread (left helix). Suitable for precision feed and positioning in milling machines.

SFK Series Ball Screws

SFK Series Ball Screws

The SFK series is a range of COMTOP ball screws designed to convert rotary motion into linear motion. The series specification table provides reference data for the ball screws and nuts, including lead, ball diameter, number of circuits, stiffness, basic dynamic load rating, and basic static load rating. Dimensions are given in millimeters (mm). The series is suitable for automation equipment, machine tools, precision positioning, and other applications.

BSH Series Ball Screws

BSH Series Ball Screws

The BSH series consists of COMTOP (TBI) rolled-grade stock ball screws. Sizes d≤14 use external ball recirculation, while sizes d≥16 use internal ball recirculation. Screw diameters range from 8~25 mm and leads from 2~5 mm, with ball circuit options including B1 / C1 / T3 / T4 and accuracy grades C7 and C10. The model code comprises six sections: nut type (BSH), screw direction (R for right-hand thread), screw diameter, lead, ball circuit turns, and rolled grade (F). The table lists the ball diameter, nut diameter, overall nut length, mounting thread, dynamic load rating Ca (151~1280 N), static load rating Coa (232~3110 N), and maximum length Ls (1200~4000 mm) for each size. These ball screws are suitable for linear motion applications such as automation equipment and machine tool feeds.