product — Page 66

WNS Series Pressure Controllers

WNS Series Pressure Controllers

WNS series pressure controllers feature an adjustable differential and are suitable for applications such as cooling water flow control and oil pressure protection. The series includes models WNS502, WNS504, WNS504H, WNS106 and WNS106H, with pressure adjustment ranges of 0.5~2, 0.5~3.5 and 1~6, oil outlet settings of 0.5 and 1, and maximum pressures of 17 or 30. The WNS502 is a low differential pressure model, while the H-suffix WNS504H and WNS106H have a maximum pressure of 30. The controllers use an SPDT single-pole double-throw microswitch, rated at 125V/250V/24V and 20A/10A/10A (AC/AC/DC), with non-harmonic current ratings of 20A/10A/10A, harmonic current ratings of 15A/8A/8A and pulse current ratings of 72A/64A. The series has no time-delay device; the pressure differential is set using an adjustment screw. It is suitable for automated fluid control systems that require switching on when the pressure differential rises or falls.

HFS Series Water Flow Switches

HFS Series Water Flow Switches

HFS series water flow switches (paddle/target-type flow switches) monitor water flow and provide interlock protection in air conditioning units, chillers, water pumps, and industrial water circulation systems. An internal single-pole double-throw (SPDT) microswitch uses a balancing spring and a moving paddle to detect liquid flow in the pipe. When the flow reaches the setpoint, the contacts actuate and provide an on/off signal for water loss protection, freeze protection, and coordinated pump control. The switches are suitable for non-corrosive liquids at pressures below 1.0MPa, ambient temperatures of 0~60℃, and liquid temperatures up to 100℃. The electrical rating is 220VAC 15A, with screw terminals and a 1/2″ cable outlet in the plastic housing. Three connection thread sizes are available: HFS-15 (PT1/2), HFS-20 (PT3/4), and HFS-25 (PT1). An adjustment screw on the housing allows the actuation flow rate to be fine-tuned on site.

CBD Series Differential Pressure Controllers

CBD Series Differential Pressure Controllers

The CBD series consists of adjustable differential pressure controllers without a time-delay device, used for cooling water flow control, oil pressure protection, and similar applications. The pressure adjustment range covers 0.5~6 (WNS502 is a low differential pressure model with a range of 0.5~2). The oil outlet setting is 0.5 or 1, and the maximum pressure is 17 or 30. The contact configuration is single-pole double-throw (common terminal 1; terminals 1~3 close as differential pressure increases, and terminals 1~5 close as differential pressure decreases). Electrical specifications: rated voltage 125VAC/250VAC/24VDC; rated current, non-harmonic 20A/10A/10A, harmonic 15A/8A/8A; pulse current 72A (125VAC) and 64A (24VDC).

SCE Series Linear Motion Unit Blocks

SCE Series Linear Motion Unit Blocks

SCE Series linear motion unit blocks are available in short (SCE...UU) and long (SCE...LUU) versions, in sizes 12 to 50. Basic load ratings range from 510 to 3820 (dynamic) and 784 to 7940 (static), with weights from 113 to 2858 g. Designed for use with LME Series linear bearings.

HWGT Series Pneumatic Vibrators

HWGT Series Pneumatic Vibrators

The HWGT series pneumatic vibrator (rotary pneumatic vibrator) is manufactured by SNS Automation (Ningbo) Group Co., Ltd. Compressed air enters through the inlet and impinges on the gear, which rotates on bearings. An eccentric steel counterweight inside the housing rotates with the gear, generating vibration through centrifugal force. Vibration force and frequency can be adjusted continuously by changing the air pressure (0.2/0.4/0.6MPa). The vibrator starts and stops instantly, responds quickly, operates quietly, delivers strong vibration, and is safe and reliable. The series includes 12 sizes (HWGT-4~HWGT-60), with a frequency range of 4750~45500 V.P.M (cycles/min), vibration force of 130~3100 N, air consumption of 30~480 l/min, air inlet size of 1/8~1/2, and weight of 260~5590 g. Typical applications include material conveying, vibratory screening, vibration-assisted discharge at material gates, package filling, and vibration of casting sand molds.

HWK Series Pneumatic Steel Ball Vibrators

HWK Series Pneumatic Steel Ball Vibrators

HWK series pneumatic steel ball vibrators use compressed air to drive a precision steel ball around the inside of a steel sleeve. The ball's eccentric rotation generates centrifugal force, producing vibration. Vibration force and frequency can be adjusted through the air supply pressure. The sealed aluminum alloy housing is suitable for wet, dusty and hazardous environments. Applications include material conveying, hopper and gate vibration, packaging and filling assistance, and vibration of foundry sand molds. Standard models range from HWK-8 to HWK-32, with operating pressures of 0.2, 0.4 and 0.6 MPa, frequencies of approximately 7500 to 34100 V.P.M, vibration forces of 245 to 4000 N, and air consumption of 90 to 680 L/min.

KR Series

KR Series

KR Series cam followers, also known as stud-type track rollers, are single-row needle roller bearings consisting of a stud and needle rollers. They are widely used in automation, conveying, and packaging equipment, as well as other applications requiring high rigidity, high load capacity, and rapid response. Their compact design allows direct mounting on a threaded shaft, and a range of sizes is available to suit different load and space requirements. The range includes standard models (KR) and models with an eccentric collar (KRE/KRVE), which allows fine adjustment of the mounting position. The outer ring is made of high-strength steel, and the optimized needle roller arrangement ensures low friction and long service life. Limiting speeds range from 5,000 to 29,000 rpm, dynamic load ratings from 280 to 2,830 N, static load ratings from 180 to 3,700 N, and weights from 16 to 1,950 g. Dimensions cover outer diameters of 13–90 mm and widths of 9–35 mm. These bearings are interchangeable with the IKO KR series.

R Series Roller Vibrators

R Series Roller Vibrators

R Series roller vibrators use compressed air to drive a steel ball or roller around inside a sleeve, producing centrifugal vibration. Vibration frequency and force can be adjusted by changing the air pressure. Their simple, safe design offers a long service life and is suitable for damp, dusty and explosion-hazard environments. Standard models include R-50, R-65, R-80 and R-100, with an operating pressure of 0.2–0.6 MPa, a frequency of approximately 11,050–36,150 V.P.M, a vibration force of 1,175–8,955 N and air consumption of 1,450–7,350 L/min. Applications include material conveying, hopper and material gate vibration, assisting with package filling and vibrating foundry sand molds.

NTP Series Reciprocating Piston Vibrators

NTP Series Reciprocating Piston Vibrators

NTP series pneumatic reciprocating piston vibrators use compressed air to drive a piston back and forth, generating vibration. They offer high power, low noise, and continuously adjustable vibration force and frequency. The nominal frequency is approximately 43~146 cycles/minute, with a vibration force of approximately 150~2039 N. The maximum operating temperature is 150℃, with a 200℃ version available on request. Applications include hopper vibration, material conveying, emptying, impact, and tapping. They are suitable for wet, dusty, and potentially explosive environments. Standard models include NTP25, NTP32, and NTP48, with dimensional and mounting interface details available.

SK Series Pneumatic Knocker

SK Series Pneumatic Knocker

The SK Series pneumatic knocker uses compressed air to drive a reciprocating piston, producing impact and vibration. It offers high power, strong impact force, and quiet operation. Its nominal frequency is 43~146 impacts/minute, with an excitation force of 150~2039 N. Frequency and amplitude can be continuously adjusted through air pressure. The maximum operating temperature is 150℃, with custom 200℃ versions available. It is suitable for vibratory emptying, conveying, impact, and tapping applications involving bins, pipes, and hoppers, and can be controlled manually or electrically.

Pneumatic Angle Seat Valve

Pneumatic Angle Seat Valve

The pneumatic angle seat valve is driven by a pneumatic actuator and is suitable for on/off control of gases, liquids, steam and other media. Nominal sizes range from DN15~DN65, connection threads from G1/2″~G2 1/2″, and actuator sizes include 50, 63, 80 and 100. Valve body lengths vary by material, such as polyurea PA or aluminum alloy. Two flow directions, A and B, are available. Direction A can extend service life and is suitable for liquids. Direction B provides better sealing with steam or gas, but prolonged contact between the U-shaped seal and the medium can reduce service life. Select a single-acting or double-acting actuator according to the nominal size and pressure. For example, a double-acting actuator is required for direction A in sizes 15/20/25 when pressure exceeds 0.3MPa.

Stainless Steel Threaded Angle Seat Valve

Stainless Steel Threaded Angle Seat Valve

The stainless steel threaded angle seat valve (pneumatic angle seat valve) features a stainless steel body and threaded connections. A pneumatic cylinder actuator moves the valve stem linearly to control shutoff and flow of media such as water, steam, oil, and gas in pipelines. It is commonly used in automated fluid control systems. The catalog covers nominal sizes from 15~100 mm, with small-head and large-head configurations available for sizes 25 and 50. The air supply port is G1/4\" (G1/8\" for the new stainless steel threaded model), with φ50, φ63, φ80, φ100, or φ125 cylinder actuators. Overall dimensions range from L 67~230 mm, A 172~420 mm, and H 147~395 mm; thread size D ranges from 1/2\" to 4\". For the same nominal size, the large-head configuration has a larger actuator and a greater overall height. Consider flow requirements and installation space when selecting a model. The plastic-head and new stainless steel models have different installation lengths and air supply port locations; specify the head type, nominal size, and actuator size when ordering.

Threaded Angle Seat Valve with Plastic Actuator Head

Threaded Angle Seat Valve with Plastic Actuator Head

The plastic-head/stainless steel threaded angle seat valve is a pneumatically controlled angle-type shutoff valve. The plastic-head version features an engineering-plastic actuator head and a threaded valve body, while the new version has a stainless steel valve body. Threaded connections range from 1/2″ to 4″ in column D, with nominal sizes of 15, 20, 25 (small/large head), 32, 40, 50 (small/large head), 65, 80, and 100 mm. The single-acting pneumatic piston actuator is available in five sizes: φ50, φ63, φ80, φ100, and φ125. The air supply port is G1/4″ on the plastic-head version and G1/8″ on the new stainless steel version. The dimension table provides installation dimensions including L (body length), A (overall height), H (centerline height), and E (actuator connection height) to facilitate piping layout and selection. The valve is suitable for shutoff and flow control of neutral media such as water, steam, and oils.

DMF Series Solenoid Pulse Valves

DMF Series Solenoid Pulse Valves

DMF series solenoid pulse valves are core components of baghouse dust collector cleaning systems. The right-angle (Z-type) design has an inlet-to-outlet angle of approximately 90°, making it easy to connect to the air header and dust collector blowpipe. It provides smooth airflow and a powerful blast, delivering the air pulses required for effective cleaning. A hard-sealing design with seal memory between the diaphragm assembly and air chamber ensures sealing performance and durability over long-term use. The series includes right-angle, submerged, threaded, straight-through, and pneumatically controlled explosion-proof designs. Nominal sizes range from G3/4"~G4" (Φ20~Φ102). The valve body is made of ADC alloy, the pilot head is made of 430FR stainless steel, and the diaphragm is made of imported nitrile rubber. Standard voltage options are AC220V, AC110V, AC24V, and DC24V, with model code positions for temperature ratings and other options.

DMF-Y Series Solenoid Pulse Valve (Immersion Type)

DMF-Y Series Solenoid Pulse Valve (Immersion Type)

The DMF-Y series comprises immersion-type, also known as embedded, solenoid pulse valves. Mounted directly on the air manifold (air tank), they offer improved flow and lower pressure loss, making them particularly suitable for applications with low air supply pressure. They are widely used in pulse-jet cleaning systems for baghouse dust collectors. The valve body, upper cover, middle cover, and small passage cover are die-cast from ADC aluminum alloy. The pilot assembly is made of 430FR stainless steel, while the large and small springs and fasteners are made of 321 stainless steel. The diaphragms and O-rings are made of imported nitrile rubber (NBR). Nominal diameters range from Φ25 to Φ102. Outlet connections are available in threaded G1″ to G1 1/2″ and embedded Ø50 to Ø102 configurations. The valves have 1 to 2 diaphragms, weigh 0.8 to 5.65 kg, and have a flow coefficient that increases with diameter.

DMF-Z Series Right-Angle Solenoid Pulse Valves

DMF-Z Series Right-Angle Solenoid Pulse Valves

The DMF-Z series comprises right-angle solenoid pulse valves, also known as submerged or embedded valves. A solenoid pilot controls the opening and closing of the diaphragm assembly to deliver an instantaneous pulse of compressed air. These valves are widely used for programmed pulse blowing in baghouse dust collectors, pulse-jet cleaning systems, and pneumatic conveying equipment. The valve body is die-cast from ADC aluminum alloy, the pilot assembly is made of 430FR stainless steel, and the large and small springs are made of 321 stainless steel. The diaphragm assembly and O-rings are made of imported nitrile rubber. Features include good flow capacity, low pressure loss, fast response, oil and wear resistance, and long service life, making the valves suitable for applications with relatively low air supply pressure. Nominal diameters range from Φ20 to Φ102. Outlet connections are available in threaded (G1″, G1 1/2″, etc.) and flanged (Ø50–Ø102) types. Working pressure is typically 0.2–0.6 MPa. Single- or double-diaphragm configurations can be selected to suit the dust collector's air manifold specifications.

DMF-ZM Series Solenoid Pulse Valves (Nut Connection)

DMF-ZM Series Solenoid Pulse Valves (Nut Connection)

The DMF-ZM series consists of nut-connection solenoid pulse valves used primarily in baghouse dust collector cleaning systems. The valve body is made of ADC aluminum alloy, the pilot head assembly of 430FR stainless steel, and the springs and fasteners of 321 stainless steel. The diaphragm is made of imported nitrile rubber, and the coil uses high-quality enamelled wire. Nominal diameters are Φ20, Φ25 and Φ40, with port sizes of 3/4″, 1″ and 1 1/2″. The valves have 1~2 diaphragms, inlet/outlet diameters of Φ27~Φ48 mm, and weights of approximately 0.9~2.0 kg. A solenoid pilot controls the opening and closing of the diaphragm, producing short, powerful pulses of compressed air for cleaning dust collector filters. The nut connections attach the valve to the air reservoir and blowpipe during installation.

KRV Series Cam Rollers

KRV Series Cam Rollers

KRV series cam rollers, also known as cam followers, are needle roller bearings with a directly rolling outer ring. They are widely used in automation equipment, industrial machinery, conveyor systems, and other applications. The series is available in 16 sizes, with outside diameters from 13 to 90 mm and widths from 9 to 35 mm. Models with an eccentric collar (KRE/KRVE) are available for preload adjustment. Limiting speeds range from 5,000 to 29,000 rpm with oil lubrication, and dynamic load ratings range from 280 to 2,830 N. The bearings feature a threaded stud (G) for easy installation and two rows of needle rollers to handle high radial loads. Standard models are KR (unsealed) and KRV (sealed); the previous designation was the NAKD series.

DMF-T Series Straight-Through Solenoid Pulse Valves

DMF-T Series Straight-Through Solenoid Pulse Valves

The DMF-T straight-through solenoid pulse valve has aligned inlet and outlet centerlines at an angle of 180°. The inlet connects to the air reservoir and the outlet to the blowpipe. Its unobstructed, low-resistance airflow path delivers cleaning pulses suited to pulse-jet cleaning systems in baghouse and cartridge dust collectors. The valve body, upper cover, middle cover and small passage cover are die-cast from ADC aluminum alloy. The pilot assembly is made of 430FR stainless steel, while the large and small springs and fasteners are made of 321 stainless steel. The general-purpose diaphragm assembly and diaphragm assembly use imported nitrile rubber (NBR), and the coil is made of high-quality enameled wire. Nominal diameters range from Φ20 upward, and the accompanying nut-type DMF-ZM subseries (Φ20/Φ25/Φ40) meets different pulse-jet airflow requirements.

MCF Series Pulse Valves

MCF Series Pulse Valves

MCF series pulse valves are high-performance diaphragm valves for dust collectors and cleaning systems, with female threaded inlet and outlet ports. They are available in electrically controlled versions (with a solenoid pilot valve, designated MCF/CA) and pneumatically controlled versions (without a pilot valve, designated RCA). The T series features 90° right-angle valves. The valve body, upper cover, and intermediate cover are die-cast ADC aluminum alloy; the pilot head assembly is 430FR stainless steel; the large and small springs are 321 stainless steel; the fasteners are 302 stainless steel; and the diaphragm is imported nitrile rubber, with fluororubber available as an option. Configurations include right-angle (1), immersed (MM), threaded (DD), and flanged (FS). Standard nominal sizes are 15, 20, 25, 35, 45, 50, 62, and 76mm, with corresponding 1/2"~3" threads. Operating pressure is 0.3~0.8MPa, and the medium is clean air. Voltage options are AC220V/AC110V/AC24V/DC24V, with an IP65 protection rating. The temperature range is -40~82℃ for nitrile diaphragms and -29~232℃ for fluororubber diaphragms. Relative humidity is ≤80%, and diaphragm life is approximately one million pulses or three years. Widely used with filter bags, filter cartridges, flat belts, and ceramic

MCF Series Solenoid Pulse Valves

MCF Series Solenoid Pulse Valves

MCF series solenoid pulse valves are diaphragm-type pulse jet valves used primarily in baghouse dust collector cleaning systems. A solenoid pilot controls the opening and closing of the diaphragm to release an instantaneous pulse of compressed air. Nominal valve diameters range from Φ25 to Φ102, with outlet connections including G1″, G1 1/2″, Φ50, Φ62, Φ76, Φ90 and Φ102. Weights range from 0.8 to 5.65 kg and flow coefficients from 26.24 to 268.29. The valves are compatible with 1″ to 4″ pulse jet piping. They use common diaphragm assemblies, and wear parts such as pilot heads, springs and O-rings are replaceable. Catalog dimensional drawings cover models MCF15 through MCF40 and MCF50 through MCF76. Values in the “number of diaphragms” column of the model table should be treated as port sizes in inches.

MCF-DD Series Right-Angle Pulse Valve

MCF-DD Series Right-Angle Pulse Valve

The MCF-DD series pulse valves are high-performance diaphragm valves with double-dresser inlet and outlet ports. The DD type features a 90° right-angle design and can be mounted directly on the air manifold for pulse-jet cleaning systems in baghouse dust collectors. Options include electrically controlled pulse valves with a solenoid pilot valve or pulse valves without a pilot valve. Key specifications include inlet and outlet inside diameters (25~40mm), port thread sizes (1", 1 1/2"), diaphragm count and flow coefficient. The valve body is made of ADC aluminum alloy; the universal diaphragm assembly and diaphragm assembly use imported nitrile rubber; the large and small springs are made of 321 stainless steel; the fasteners and sealing rings are made of 302 stainless steel; and the pilot head assembly is made of 430FR stainless steel. The coil uses high-quality enameled wire. In addition to the 25DD and 45DD, the series includes models for a range of blowpipe diameters (50/62/76/89/90/102mm, etc.), which can be selected according to the air manifold position and mounting hole dimensions.

AMF Series Pulse Valves

AMF Series Pulse Valves

AMF series pulse valves are solenoid pulse valves designed for pulse-jet cleaning systems in baghouse dust collectors. Their right-angle valve body provides high flow, long service life and rapid opening and closing, ensuring reliable, stable operation. The body is die-cast ADC alloy, with a 430FR stainless steel pilot assembly, a 321 stainless steel main spring, 302 stainless steel fasteners and an imported nitrile rubber/TPE diaphragm assembly. There is no threaded shaft to seize, making maintenance quick and easy. Operating pressure is 0.4~0.6MPa, and the operating medium is clean air. Three standard voltages are available: DC24V (0.8A), AC110V (0.46A) and AC220V (0.23A). Relative air humidity is ≤85%, and the protection rating is IP65. Temperature ratings are class 1 (-25~80℃), class 2 (-25~150℃) and class 3 (-25~230℃). Bore sizes range from 25~75mm, with pipe connections from 3/4" to 3". Configurations include A right-angle and B drip-type, with the optional J improved design.

MCF FS Series Solenoid Pulse Valves

MCF FS Series Solenoid Pulse Valves

The MCF FS series is a second generation of ultra-high-performance solenoid pulse valves, also known as pulse cleaning valves, designed primarily for pulse-jet cleaning systems in baghouse dust collectors. The valve inlet has a flange connection, while the outlet slips directly onto the blow pipe for easy installation and removal. Options include an electrically controlled pulse valve with a solenoid pilot (CA) or a pneumatically controlled pulse valve without a pilot. The FS type has a straight-through valve design. The operating pressure range is 0.4~0.6MPa. Diaphragms are available in nitrile rubber (Nitrile, -40℃~82℃) or fluororubber (Viton, -29℃~232℃) for different temperature conditions. Common models include MCF25FS (1 diaphragm, flow coefficient 22/25) and MCF45FS (2 diaphragms, flow coefficient 52/61). The inlet and outlet connection pipe inside diameters and the blow pipe outside diameter increase with model size.

EX Series Explosion-Proof Coils

EX Series Explosion-Proof Coils

EX series explosion-proof coils are solenoid coils designed for use with various explosion-proof solenoid valves in environments containing explosive gases. The series includes EX1320, EX1420, and EX1620 models, with EX1320 available in sizes 11, 12.5, and 13.7. Standard voltages are AC220V and DC24V, with corresponding standard power ratings of AC25VA and DC15W. The coils use cable leads for connection, carry the explosion-proof marking Exmb11T4, and have explosion-proof certificate CNEX17.3311X. They can be used with a wide range of explosion-proof solenoid valves. When selecting a coil, match the model to the valve body interface, voltage, and power requirements, and verify the explosion-proof rating and temperature class for the operating environment.

AC Series Air Preparation Units

AC Series Air Preparation Units

AC series air preparation units filter, regulate and lubricate compressed air, combining a filter, regulator and lubricator in one assembly. AC1010~AC5010 models are two-piece variants combining a filter regulator and lubricator. The units have a proof pressure of 1.5MPa, a maximum operating pressure of 1.0MPa and an ambient and fluid temperature range of 5~60℃. Standard filtration is 25μm, with 5μm and 50μm options. The pressure adjustment range is 0.05~0.85MPa, and the regulator is relieving type. The bowls are polycarbonate, with protective guards on AC3000-5000 but not AC2000. No. 1 turbine oil ISO VG32 is recommended. Models range from AC1000~AC5000 and AC1010~AC5010, with port sizes M5~1, rated flow rates of 90~5000 L/min and a choice of Rc/NPT threads.

SYX Series Precision Linear Guide Rails

SYX Series Precision Linear Guide Rails

The SYX Series Precision Linear Guide Rail is a high-precision linear motion component designed for automated machinery, material-handling equipment, machine tools, and other applications. It is available with multiple assembly heights (H/S/X), sizes (15–65), flange types (BN/BL/BE/BS/FN/FS/FL/FE), dust-protection classifications, and preload grades (ZF/ZO/Z1/Z2/Z3) to meet various load and accuracy requirements. A wide range of rail lengths is available, with configurations supporting 1–3 blocks per rail and multiple rails installed in parallel on the same plane. Multiple anti-corrosion surface-treatment options are available. Accuracy grades include C/H/P/SP/UP. The clear coding system enables quick identification of each parameter through an alphanumeric combination.

Cylindrical Linear Guide Shaft Series

Cylindrical Linear Guide Shaft Series

The cylindrical linear guide shaft series includes standard (GF, TF), chrome-plated (GD, TD), and stainless steel (FS) subseries. Shafts are made of GCr15 or 45# high-carbon steel, with a hardness of HRC 62+2 (45#: HRC 58), a surface hardening depth of 0.8–2.5 mm, surface roughness of 0.8–1.6S, straightness of 80 μm/1000 mm, and roundness of no more than 3.0 μm. Solid and hollow linear shafts are available. Solid shaft sizes are compatible with all of our linear bearings; hollow shafts are available only in diameters greater than 12 mm. Shaft diameters range from 3 mm to 80 mm, with a G6 tolerance grade. Special shafts with threaded holes are available for connection to support rails.

AC Series Air Preparation Units

AC Series Air Preparation Units

The AC series combines a filter (AF), regulator (AR), and lubricator (AL) in a three-piece air preparation unit for filtering, pressure regulation, and oil mist lubrication of compressed air upstream of pneumatic systems. Key specifications: proof pressure 1.5MPa (15kgf/cm²); maximum operating pressure 1.0MPa (10kgf/cm²); ambient and fluid temperature 5-60℃; standard filtration rating 25μm (5μm and 50μm also available); recommended oil: turbine oil No. 1 ISO VG32; bowl material: polycarbonate. AC1000 and AC2000 have no bowl guard; AC3000-5000 have bowl guards. Pressure adjustment range: 0.05-0.85MPa (0.5-8.5kgf/cm²); valve type: relieving. Six sizes are available by bowl and port size: AC1000, AC2000, AC2500, AC3000, AC4000, and AC5000. Port sizes range from M5 to 3/4, with Rc and NPT threads also available. Optional Y10L/Y20L/Y30L/Y40L/Y50L

AC Series Air Preparation Units

AC Series Air Preparation Units

AC series air preparation units combine an AF filter, an AR regulator (relieving type), and an AL lubricator to filter, regulate, and lubricate compressed air. They are widely used with pneumatic actuator systems. Proof pressure is 1.5MPa, maximum operating pressure is 1.0MPa, and ambient and fluid temperature is 5~60℃. Standard filtration rating is 25μm, with 5 and 50μm options available. No. 1 turbine oil ISO VG32 is recommended, and the bowl is made of polycarbonate. The pressure adjustment range for AC2000~AC5000 is 0.05~0.85MPa. Models range from AC1000~AC5000, with port sizes M5, 1/8, 1/4, 3/8, 1/2, and 3/4. Rc and NPT threads are also available.

AL Series Lubricators

AL Series Lubricators

The AL series lubricator is the lubrication component of the AC series three-piece air preparation unit. It atomizes lubricating oil into compressed air to lubricate downstream pneumatic components such as cylinders and pneumatic valves. It can be combined with AF series filters and AR series regulators, and is available in AL1000, AL2000, AL3000, AL4000, and AL5000 sizes. The listed air preparation specifications include a proof pressure of 1.5MPa, a maximum operating pressure of 1.0MPa, an ambient and fluid temperature range of 5-60℃, recommended No. 1 turbine oil ISO VG32, and a polycarbonate bowl. AC2000 has no bowl guard, while AC3000-5000 have bowl guards. The regulator pressure range is 0.05-0.85MPa, and the regulator is a relieving type. The 25μm filtration rating applies to the filter, with 5 and 50μm options also available.

AF Series Air Filters

AF Series Air Filters

AF Series air filters are air preparation components for pneumatic systems, designed to remove moisture and contaminants from compressed air. Available in five sizes—AF1000, AF2000, AF3000, AF4000 and AF5000—they cover port sizes from M5 to 1 inch, with Rc and NPT threads also available. Rated flow is approximately 110–7000 L/min. Some sizes can be fitted with an automatic drain (models B240/B340/B440/B540/B640) for automatic water removal. Flow is tested at a supply pressure of 0.7MPa and a set pressure of 0.5MPa. Suitable for air purification and moisture removal in a wide range of pneumatic circuits, these filters serve as the filtration unit in a standard three-piece air preparation assembly.

AR Series Pressure Regulators

AR Series Pressure Regulators

AR series pressure regulators are relieving-type pneumatic pressure control components designed to reduce compressed air pressure and maintain a stable output pressure in air preparation systems. The guaranteed proof pressure is 1.5MPa, the maximum operating pressure is 1.0MPa, and the pressure adjustment range is 0.05~0.85MPa (2000~5000 series). The ambient and fluid temperature range is 5~60℃. Models range from AR1000~AR5000, with port sizes of M5, 1/8, 1/4, 3/8, 1/2, 3/4 and 1, rated flow rates of 100~8000L/min, and weights of 0.08~1.19kg. The standard configuration includes brackets (2) and a pressure gauge, with gauge port sizes of 1/16~1/4. Rc and NPT port threads and filtration ratings of 5 and 50μm are also available.

AL Series Air Lubricators

AL Series Air Lubricators

The AL series air lubricator uses the Venturi principle to atomize lubricating oil and mix it with compressed air, lubricating downstream pneumatic components such as cylinders and air motors. Proof pressure is 1.5MPa (15kgf/cm²), maximum operating pressure is 1.0MPa (10kgf/cm²), and ambient and fluid temperatures are 5~60℃. The recommended oil is No. 1 turbine oil ISOVG32, and the bowl is made of polycarbonate. The AL2000 has no bowl guard; the AL3000~5000 have bowl guards. Five sizes are available: AL1000, AL2000, AL3000, AL4000, and AL5000. Port sizes range from M5~1, rated flow from 95~7000 L/min, minimum flow for oil dripping from 4~190 L/min, bowl capacity from 7~130 cm³, and weight from 0.07~1.08 kg. Optional B240~B640 brackets are available (2 pieces). Flow rates in the table are measured at a supply pressure of 0.5MPa, an oil drip rate of 5 drops/minute, and an ISOVG32 oil temperature of 20℃. Rc and NPT port threads are also available.

AL Series Lubricators

AL Series Lubricators

AL series lubricators provide oil-mist lubrication in compressed air lines, atomizing No. 1 turbine oil (ISO VG32) and delivering it to downstream pneumatic components to reduce wear. They use polycarbonate bowls; AL3000~AL5000 models have protective covers, while AL2000 models do not. Proof pressure is 1.5MPa, maximum operating pressure is 1.0MPa, and ambient and fluid temperatures are 5~60℃. Port sizes range from M5 and 1/8~1 inch, with rated flow rates of 95~7000 L/min, minimum oil drip flow rates of 4~190 L/min, and bowl capacities of 7~130 cm³. Model numbers combine the AL body size and port code, as in AL2000-01 and AL5000-10. B240/B340/B440/B540/B640 brackets are available as options.

AW Series Filter Regulators

AW Series Filter Regulators

AW series filter regulators combine air filtration and pressure regulation for pneumatic systems. They have a proof pressure of 1.5MPa, a maximum operating pressure of 1.0MPa, and an ambient and fluid temperature range of 5-60℃. The standard filtration rating is 25μm, with 5μm and 50μm options, and the bowl is made of polycarbonate. The AW2000 has no protective cover, while the AW3000-5000 have protective covers. The AW2000-5000 have a pressure adjustment range of 0.05-0.85MPa and are relieving-type valves. Port sizes range from M5 to 3/4-1. Models include AW1000, AW2000, AW3000, AW4000, AW4000-06, and AW5000. The dimension table provides A-P overall and mounting dimensions for each model. These units are suitable for air preparation in various pneumatic circuits.

IR Series Precision Pressure Regulators

IR Series Precision Pressure Regulators

IR series precision pressure regulators provide precise pressure reduction and stabilization of compressed air in pneumatic systems. They are compact and lightweight, with accurate pressure settings. The adjustment screw thread pitch has been reduced from the conventional 0.75mm to 0.5mm for finer adjustment. They can be mounted independently with a bracket or directly combined with AF and AFM modular filter units. The standard model supports panel mounting, and the pilot exhaust port is separate from the main exhaust port. Special-order models are available for use in clean environments. Compared with the conventional IR200 precision regulator, the IR3000 offers higher output and relief flow rates. Pressure setting ranges include 0.005-0.2MPa, 0.01-0.4MPa and 0.01-0.8MPa. Repeatability is within ±0.5% of full scale, ambient and fluid temperatures are -5~60℃ (no freezing), maximum operating pressure is 1.0MPa, and the pressure port size is Rc1/8. An air filter (AF) and an oil mist separator (AM, AFM) must be installed on the supply side.

TF Series Precision Shaft

TF Series Precision Shaft

The TF series cylindrical linear guide shafts (precision shafts) are made from GCr15 or 45# high-carbon steel, with a hardness of HRC 62 (+2) (HRC 58 for 45# steel). The case-hardening depth is 0.8–2.5 mm, surface roughness is 0.8–1.6 S, straightness is 80 μm per 1,000 mm, and roundness is no greater than 3.0 μm (Rmax). Solid and hollow shafts are available. Solid shafts range from Φ3 to Φ80 (G6 tolerance); hollow shafts are available only in diameters over 12 mm. Custom shafts can also be made, such as versions with threaded holes for connection to support rails. Designed for use with a range of linear bearings, these shafts provide a high-precision, long-life linear motion solution.

GF Series Water Separators

GF Series Water Separators

GF series water separators remove moisture and filter solid particles from compressed air lines. A copper flow-guiding structure induces rotation in the airflow, improving liquid separation and reliably filtering solid particles. The separators feature low pressure drop, high water separation efficiency and a large bowl capacity. Filtration ratings of 5μm and 40μm are available, with manual, differential-pressure or automatic drainage. An optional mounting bracket is also available. The body is aluminum alloy, the O-ring is NBR, the flow guide is high-viscosity POM, and the filter element is sintered bronze particles (40μm). The filter bowl is aluminum alloy on the GF600 and PC on other models. The level gauge protective cover is SPCC, the level gauge sealing gasket is fluororubber, and the level gauge inner cover is PC.

GR Series Pressure Regulators

GR Series Pressure Regulators

GR series pressure regulators regulate and stabilize pressure in pneumatic systems. An integrated square pressure gauge saves installation space, while an external round gauge is also available. A pressure-locking mechanism prevents external interference from affecting the set pressure, and a balanced regulating mechanism provides greater stability with minimal drift. The series includes GR200, GR300, GR400 and GR600 models, with port sizes from PT1/8 to PT1. The standard operating pressure range is 0.05~0.9MPa (20~130psi), the proof pressure is 1.5MPa (215psi), and the operating temperature range is -20~70℃. In addition to the standard version, options include the L low-pressure version, with or without a gauge, square or round gauges, different scale units and filtration ratings. Custom pressure specifications are also available (maximum adjustable pressure 0.4MPa).

GL Series Lubricator

GL Series Lubricator

The GL series lubricator is an air preparation device that delivers small amounts of oil mist into compressed air to protect downstream pneumatic components such as cylinders and solenoid valves. Its rounded, sealed drip mechanism provides smooth, reliable oil-flow adjustment. The adjustment knob rotates one full turn, with oil flow varying approximately linearly across the scale, allowing the flow rate to be estimated from the setting. A specially designed drip nozzle creates negative pressure at the outlet, enabling oil delivery at low airflow rates. The large oil bowl can be refilled without shutting down the system, and the unit can be mounted using a bracket. The working medium is air, with an operating pressure range of 0.05~0.9MPa (7~130psi), a proof pressure of 1.5MPa (215psi), and an operating temperature of -20~70℃. Port sizes range from PT1/8~PT1. Oil bowl capacity is 25CC or 75CC, and weight is 130g or 360g. ISO VG32 or equivalent oil is recommended. The body is aluminum alloy; the GL600 oil bowl is aluminum alloy, while the bowls for other sizes are PC.

GFR Series Filter Regulators

GFR Series Filter Regulators

The GFR series filter regulator is a key component of air preparation (FRL) systems, combining filtration and pressure regulation to clean compressed air and set it to the required pressure. A recessed square pressure gauge saves installation space, while an external round gauge is available as an option. A self-locking pressure adjustment mechanism prevents external interference from changing the set pressure, and a balanced regulation mechanism provides stable adjustment, minimal drift and excellent pressure characteristics. A unique flow-guiding structure creates a controlled swirl, separating and draining moisture from the air more effectively. Filtration ratings of 5μm and 40μm are available, along with manual, differential-pressure and automatic drain options. A mounting bracket is also available. In addition to the standard version, a low-pressure version is available with a maximum adjustable pressure of 0.4MPa. The range includes the GFR200, GFR300, GFR400 and GFR600 series, classified by port size.

GFC Series Air Filters

GFC Series Air Filters

GFC series air filters provide air preparation for pneumatic systems, with quick, secure connections for easy installation and use. They offer stable, repeatable pressure regulation and efficiently remove moisture and solid particles from compressed air. Three drain options are available: manual, differential pressure and automatic. Filtration ratings are 40μm or 5μm, with optional square or round pressure gauges and a reverse-flow valve. Port sizes range from PT1/8 to PT1, operating pressure is 0.15~0.9MPa, and operating temperature is -20~70℃. Filter bowl capacity is 10CC/40CC and drain capacity is 25CC/75CC. The filters can be combined with GFR series indicating components and GL series lubricators to form a three-piece air preparation unit.

GFR Series Pressure Regulator

GFR Series Pressure Regulator

The GFR series pressure regulator is the pressure control unit in the air preparation three-piece assembly (GFC filter + GFR pressure regulator + GL lubricator). It reliably reduces compressed air line pressure to a set value with good repeatability and can be quickly and securely assembled with GFC series filters and GL series lubricators of the same port size. The working medium is air. Port sizes include PT1/8, PT1/4, PT3/8, PT1/2, PT3/4 and PT1, across four sizes: 200/300/400/600 (port codes 06/08/10/15/20/25). Common parameters for the three-piece assembly are: operating pressure range approximately 0.15~0.9 MPa (automatic and differential-pressure drain types), operating temperature -20~70℃, filtration rating 40μm or 5μm, and ISO VG 32 or equivalent oil for filter element cleaning. Square or round gauges are available with scales in MPa, psi or bar. A reverse flow valve is also optional.

GL Series Lubricators

GL Series Lubricators

GL series lubricators are lubrication components for pneumatic air preparation systems. Used with GFC series filters, they provide a consistent oil mist to lubricate downstream pneumatic actuators. The catalog includes four size ranges: GL200, GL300, GL400, and GL600, with port sizes including PT1/8, PT1/4, PT3/8, PT1/2, PT3/4, and PT1 to meet the needs of air circuits with different flow rates. Each model corresponds to a GFC filter of the same size (for example, GL200-06 corresponds to GFC200-06), making it easy to assemble a matching air preparation unit. Select the appropriate size based on the air line connection, flow rate, and available installation space.

GC Series Air Lubricators

GC Series Air Lubricators

GC series air lubricators provide lubrication and air purification for pneumatic systems. The range comprises four sizes—GC200, GC300, GC400 and GC600—with port sizes from PT1/8 to PT1. The corrosion-resistant oil reservoir seal provides stable, reliable oil-feed adjustment. The oil-feed adjustment tube threads are standardized, and oil delivery follows an approximately linear scale, allowing the flow rate to be estimated from the setting. Oil can be added without shutting down the system. A special reservoir design creates negative pressure at the oil outlet and requires a low initial flow rate. Pressure regulation is stable and highly repeatable, while connections are quick and secure and installation is precise. Drain options include differential-pressure drain (blank), M manual drain and A automatic drain. The units also efficiently remove moisture and solid particles. The ordering code combines the series, port size, drain type, pressure gauge code, scale unit and oil filtration accuracy in sequence. Scale units are available in MPa, psi or bar.

AC/BC Series FRL Units

AC/BC Series FRL Units

AC/BC series FRL units (air preparation units) combine a filter (AF/BF), pressure regulator (AR/BR), and lubricator (AL/BL) to clean, regulate, and lubricate the air supply in pneumatic systems. AC is the compact series, and BC is the medium-size series. Port sizes include G1/8", G1/4", G3/8", and G1/2". Filtration rating: 40μm; pressure adjustment range: 0.05~0.85MPa; maximum adjustable pressure: 0.95MPa; proof pressure: 1.5MPa; operating temperature: 5~60℃; filter bowl capacity: 15cc; lubricator bowl capacity: 25cc. The body is die-cast aluminum alloy, and the bowls are PE. ISOVG32 or equivalent lubricating oil is recommended. Weight: approximately 0.7kg. The ordering code consists of the model (AC/BC), size specification (1500/2000/3000/4000), and drain type (D).

AFC/BFC Series Two-Piece Air Preparation Units

AFC/BFC Series Two-Piece Air Preparation Units

AFC/BFC series two-piece air preparation units combine a filter regulator (AFR/BFR) with a lubricator (AL/BL). They filter and reduce the pressure of compressed air and provide oil-mist lubrication, supplying cylinders, pneumatic valves and other downstream actuators with clean, pressure-regulated, oil-misted compressed air. AFC units are compact (port size G1/8"~G1/4"), while BFC units are medium-sized (port size G1/4"~G1/2"). Key specifications: operating fluid: air; filter element rating: 40μ; pressure adjustment range: 0.05~0.85MPa; maximum adjustable pressure: 0.95MPa; proof pressure: 1.5MPa; operating temperature: 5~60℃. Compact units have a 15cc filter bowl and a 25cc oil bowl; medium units have a 60cc filter bowl and a 90cc oil bowl. ISOVG32 or equivalent lubricating oil is recommended. The body is die-cast aluminum alloy, the bowls are PE, and the protective bowl guards are iron. Weight is approximately 0.5kg for compact units and 0.7kg for medium units.